Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-04T21:28:50.339Z Has data issue: false hasContentIssue false
  • English
  • Français

Flexible Magnetics: Magnetic Lithography and Fabrication of Magnetic Masks on Thin Plastic Substrates

Published online by Cambridge University Press:  15 February 2011

Z. Z. Bandić ,
H. Xu ,
J.E.E. Baglin  and
T. R. Albrecht
Z. Z. Bandić
Affiliation:
Hitachi San Jose Research Center 650 Harry Rd., San Jose, CA 95120
H. Xu
Affiliation:
Hitachi San Jose Research Center 650 Harry Rd., San Jose, CA 95120
J.E.E. Baglin
Affiliation:
IBM Almaden Research Center, 650 Harry Rd., San Jose, CA 95120
T. R. Albrecht
Affiliation:
IBM Almaden Research Center, 650 Harry Rd., San Jose, CA 95120
Get access

Abstract

Flexible magnetic lithography is a process qualitatively analogous to contact optical lithography which transfers information from a patterned magnetic mask (analog of optical photomask) to magnetic media (analog of photoresist), and is interesting for applications in instantaneous parallel magnetic recording. The magnetic mask consists of patterned soft magnetic material (FeNiCo, FeCo) on a flexible plastic substrate, typically Polyethylene Teraphtalate (PET). When uniformly magnetized media is brought into intimate contact with the magnetic mask, an externally applied magnetic field selectively changes the magnetic orientation in the areas not covered with the soft magnetic material. Flexible substrate of the magnetic mask o.ers superior compliance to magnetic media which is likely to have imperfect flatness and surface particulate contamination.

Although magnetic in physical nature, flexible magnetics draws interesting parallels to flexible electronics, especially in challenges of fabrication of sub-micron patterns on thin flexible plastic substrates. We fabricated samples of sub-micron patterned FeCo and FeNiCo magnetic masks on PET substrates by using combined lamination/release process of PET films. Rigid substrates, typically silicon or quartz were initially laminated with PET films and processed using standard fabrication procedures. After completing magnetic mask device fabrication, PET films were released from the rigid substrates.

We successfully transferred patterns from magnetic masks to hard disk CrPtCo-based magnetic media. The details of the method, including physics of the magnetic lithography pattern transfer, fabrication of the magnetic mask on flexible PET substrates, lamination and release of PET films, and magnetic force microscopy (MFM) images of the magnetic transition patterns are reported.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 769: Symposium H – Flexible Electronics - Materials and Device Technology , 2003 , H7.1
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Bernard, W.R., Buslik, W.S., US pat. 3,869,711Google Scholar
[2] Bandić, Z.Z., Xu, H., Albrecht, T.R., Appl. Phys. Lett. 82, 147 (2003).Google Scholar
[3] Tanaka, S., Imai, Y., Morita, O., Dericotte, D., Kurokawa, K., Kashiwagi, T., and Takino, H., IEEE Trans. Magn. 30, 4209 (1994).Google Scholar
[4] Terris, B.D., Folks, L., Weller, D., Baglin, J.E.E., Kellock, A.J., Rothuizen, H. and Vettiger, P., Appl. Phys. Lett. 75, 403 (1999).Google Scholar
[5] Dietzel, A., Berger, R., Grimm, H., Bruenger, W.H., Dzionk, C., Letzkus, F., Springer, R., Loeschner, H., Platzgummer, E., Stengl, G., Bandić, Z.Z., and Terris, B.D., IEEE Trans. Magn. 38, (2002).Google Scholar
[6] Saito, A., Yonezawa, E., Takano, Y., and Watanabe, T., J. Appl. Phys. 91, 8688 (2002).Google Scholar
[7] Xu, H., Dinan, T.E., Cooper, E.I., Romankiw, L.T., Bonhote, C., and Miller, D., Proc. of the Electrochem. Soc., PV 2001-8.Google Scholar
[8] Baglin, J.E.E., Intreface Design for Thin Film Adhesion, Fundamentals of Adhesion, ed. by Lee, L-H., Plenum Publ. Corp., 13 (1991).Google Scholar
[9] Kim, K-S. and Kim, J., Trans. ASME 110, 266 (1988).Google Scholar