Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-17T15:13:54.245Z Has data issue: false hasContentIssue false
  • English
  • Français

Excimer Laser Processing of Tool Steel: Tribological Effects of Multiple Pulse Processing and Ti Alloying

Published online by Cambridge University Press:  15 February 2011

T. R. Jervis ,
M. Nastasi ,
A. J. Griffin Jr. ,
T. G. Zocco ,
T. N. Taylor  and
S. R. Foltyn
T. R. Jervis
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
M. Nastasi
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
A. J. Griffin Jr.
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
T. G. Zocco
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
T. N. Taylor
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
S. R. Foltyn
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545
Get access

Abstract

Excimer lasers were used to modify the surface of AISI type A-7 tool steel, a high C, high V, high Cr material used in many cutting applications. Multiple pulses of laser radiation at 248 nm were used to alter the composition of the surface alloy. Hardness and modulus were not significantly affected by the treatment, but friction in dry sliding against an alumina pin was reduced. The reduction was small but persistent for multiply melted and resolidified surfaces. These surfaces showed a marked increase in the surface Cr concentration. Greater reductions in friction were obtained from a Ti rich surface layer formed by laser mixing an evaporated Ti layer into the material. The friction coefficient of the Ti alloyed surface deteriorated after approximately 1,000 cycles, indicating wear-through of the modified surface. The observed properties will be discussed in terms of the excimer laser modification process and the microstructure and composition of the resulting surfaces.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 397: Symposium B – Advanced laser Processing of Materials-Fundamentals and Applications , 1995 , 531
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Jervis, T. R., Hirvonen, J-P., & Nastasi, M., Lubrication Engineering 48 141 (1992)Google Scholar
2 Jervis, T. R., Nastasi, M., Hirvonen, J-P., & Hubbard, K. M., J. Am. Ceram Soc. 76 350 (1993)Google Scholar
3 Jervis, T. R., Nastasi, M., & Hirvonen, J-P., Mater. Res. Soc. Symp Proc. 279 665–678 (1993)Google Scholar
4 Pethica, J. B., in Ion Implantation into Metals, Ashworth, V., Grant, W. A., and Proctor, R. P. M., Eds, (Pergamon Press, Oxford, 1982), pp 147–156.Google Scholar
5 Oliver, W. C. & Pharr, G. M., J. Mater. Res. 7 1564 (1992).Google Scholar
6 Fabes, B. D., Oliver, W. C., McKee, R. A., & Walker, F. J., J. Mater. Res. 7 356–364 (1992).Google Scholar
7 Doerner, M. F. & Nix, W. D., J. Mater. Res. 1 601 (1986).Google Scholar
8 Jervis, T. R., Williamson, D. L., Hirvonen, J-P., & Zocco, T. G., Materials Lett. 9 379 (1990)Google Scholar
9 Doolittle, L. R., Nucl. Inst. & Meth. B15 227 (1986).Google Scholar
10 Nastasi, M. & Mayer, J. W., Mat. Sci. Reports, 6 1 (1991)Google Scholar
11 Jervis, T,. R. & Hirvonen, J-P., Wear 150 259 (1991)Google Scholar