Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T17:31:39.851Z Has data issue: false hasContentIssue false
  • English
  • Français

The Effects of Annealing Temperature on Tensile Properties in a Fine-grained Fe3Al-based Alloy Containning κ-Fe3AlC Carbide Particles

Published online by Cambridge University Press:  01 February 2011

Akira Takei ,
Satoru Kobayashi  and
Takayuki Takasugi
Akira Takei
Affiliation:
[email protected], Osaka Prefecture University, Materials Science, Sakai, Japan
Satoru Kobayashi
Affiliation:
[email protected], Osaka Center for Industrial Materials Research, Institute for Materials Research, Tohoku University, Sakai, Japan
Takayuki Takasugi
Affiliation:
[email protected], Osaka Prefecture University, Sakai, Japan
Get access

Abstract

The effects of annealing temperature on the room temperature tensile properties were investigated in a fine-grained Fe3Al based-alloy, and the correlation between microstructure, texture and tensile properties was discussed. Tensile elongation showed a peak as a function of annealing temperature. The highest elongation was obtained in the recrystallized samples annealed at 700°C. The decrease in the elongation with increasing annealing temperature above 700°C is attributed to the increase in the fraction of <100> oriented grains with respect to the tensile direction. A high sensitivity to environmental embrittlement was observed in the partially recrystallized samples annealed at 650°C.

Keywords

ductilitytexturegrain size
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1128: Symposium U – Advanced Intermetallic-Based Alloys for Extreme Environment and Energy Applications , 2008 , 1128-U05-11
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Stoloff, N.S., Mater. Sci. Eng. A 258, 1 (1998).Google Scholar
2. McKamey, C.G. and Pierce, D.H., Scr. Metall. 28, 1173 (1993).Google Scholar
3. Huang, Y.D., Yang, W.Y., Chen, G.L., Sun, Z.Q., Intermetallics 9, 331 (2001).Google Scholar
4. Morris, D.G. and Leboeuf, M., Acta mater. 42, 1817 (1994).Google Scholar
5. Lynch, R.J., Gee, K.A. and Heldt, L.A., Scr. Metall. 30, 945 (1994).Google Scholar
6. Kobayashi, S., Zaefferer, S., Intermetallics 14, 1252 (2006).Google Scholar
7. Kobayashi, S., Zaefferer, S., Raabe, D., Mater. Sci. Forum 550, 345 (2007).Google Scholar
8. Kobayashi, S., Zaefferer, S., Mater. Sci. Forum 558–559, 235 (2007).Google Scholar
9. Kobayashi, S., Zaefferer, S., Proc of Mater. Res. Society Symp. proc. 980, II01 (2007).Google Scholar
10. Kobayashi, S., Takasugi, T., Intermetallics 15, 1659 (2007)9.Google Scholar
11. Kobayashi, S., Takei, A., Takasugi, T., Structural Aluminides for Elevated Temperature Applications, edited by Kim, Young-Won, (TMS Publishers, New Orleans, 2008), p. 383.Google Scholar
12. Chao, J., Morris, D.G., Munoz-Morris, M.A., Gonzalez-Carasco, J.L., Intermetallics 9, 299 (2001).Google Scholar