Hostname: page-component-cd9895bd7-7cvxr Total loading time: 0 Render date: 2024-12-27T02:04:43.605Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of Boron Addition on Magnetostrictive and Mechanical Properties in Rolled Polycrystalline Fe-187%Ga Alloy

Published online by Cambridge University Press:  01 February 2011

Suok-Min Na  and
Alison B. Flatau
Suok-Min Na
Affiliation:
[email protected], University of Maryland, Aerospace Engineering, 3181 Glenn L. Martin Hall, College Park, Maryland, 20742, United States, 301-405-1131, 301-314-9001
Alison B. Flatau
Affiliation:
[email protected], University of Maryland, Aerospace Engineering, United States
Get access

Abstract

During attempts to roll Fe-18.7%Ga alloy (atomic%), an alloy of interest because single crystal samples exhibit magnetostriction of ∼400 ppm, cracks formed along grain boundaries and subsequently samples fractured during hot rolling such that the alloy was too brittle to make thin sheets. While variations to rolling schedules (temperatures, times, roll diameters, etc.) may improve rollability, in this paper we investigate the effect of boron addition on Fe-18.7% Ga alloy magnetostrictive and mechanical properties. Thin sheets of Fe-18.7%Ga alloy plus 0.5 and 1.0 at.%B were successfully fabricated to thickness of 0.35 mm using rolling processes. It was observed that the fracture surface of the B-free alloy clearly appeared as an intergranular fracture mode and that of the B-added alloys was changed to a transgranular fracture mode with grain refinement. The annealed sheets with boron content of 0.5 and 1.0 at.% exhibit the maximum magnetostriction values of 103 and 184 ppm, respectively. In the case of Fe-18.7%Ga plus 1.0 %B, Fe2B phase presents throughout the α-iron matrix in small amount.

Keywords

magnetic propertiesAuger electron spectroscopy (AES)scanning electron microscopy (SEM)
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 888: Symposium V – Materials and Devices for Smart Systems II , 2005 , 0888-V06-07
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Clark, A. E., Hathaway, K. B., Wun-Fogle, M., Restorff, J. B., Lograsso, T. A., Keppens, V. M., Petculescu, G. and Taylor, R. A.: Extraordinary magnetoelasticity and lattice softening in bcc Fe-Ga alloys. J. Appl. Phys. 93, 8621 (2003).Google Scholar
2. Kellogg, R. A., Flatau, A. B., Clark, A. E., Wun-Fogle, M. and Lograsso, T. A.: Texture and grain morphology dependencies of saturation magnetostriction in rolled polycrystalline Fe83Ga17 . J. Appl. Phys. 93, 8495 (2003).Google Scholar
3. Srisukhumbowornchai, N. and Guruswamy, S.: Crystallographic textures in rolled and annealed Fe-Ga and Fe-Al alloys. Metall. and Mater. Trans. A 35A, 2963 (2004).Google Scholar
4. Cohron, J. W., Lin, Y., Zee, R. H. and George, E. P.: Room-temperature mechanical behavior of FeAl: Effects of stoichiometry, environment, and boron addition. Acta Mater. 46, 6245 (1998).Google Scholar
5. George, E. P., Gubbi, A. N., Baker, I. and Robertson, L.: Mechanical properties of soft magnetic FeCo alloys. Mater. Sci. Engng. A 329–331, 325 (2002).Google Scholar
6. George, E. P. and Liu, C. T.: Brittle fracture and grain boundary chemistry of microalloyed NiAl. J. Mater. Res. 5, 754 (1996).Google Scholar
7. Godfrey, T. M. T., Wisbey, A., Goodwin, P. S., Bagnall, K. and Ward-Close, C. M.: Microstructure and tensile properties of mechanically alloyed Ti-6Al-4V with boron additions. Mater. Sci. Engng. A 282, 240 (2000).Google Scholar
8. Song, S.-H., Guo, A.-M., Shen, D.-D., Yuan, Z.-X., Liu, J. and Xu, T.-D.: Effect of boron on the hot ductility of 2.25Cr1Mo steel. Metals and Engng. A 360, 96 (2003).Google Scholar
9. Jahazi, M. and Jonas, J. J.: The non-equilibrium segregation of boron on original and moving austenite grain boundaries. Mater. Sci. Engng. A 335, 49 (2002).Google Scholar
10. Pang, L., Han, S. M. and Kumar, K. S.: Tensile response of an Fe-40Al-0.7C-0.5B alloy. Acta Mater. 50, 3623 (2002).Google Scholar
11. Kim, K. N., Pan, L. M., Lin, J. P., Wang, Y. L., Lin, Z. and Chen, G. L.: The effect of boron content on the processing for Fe-6.5 wt% Si electric steel sheets. J. Magn. Magn. Mater. 277, 331 (2004).Google Scholar
12. Yoshitomi, Y., Iwayama, K., Nagashima, T., Harase, J. and Takahashi, N.: Coincidence grain boundary and role of inhibitor for secondary recrystallization in Fe-3%Si alloy. Acta Metal. Mater. 41, 1577 (1993).Google Scholar
13. Park, J. Y., Han, K. S., Woo, J. S., Chang, S. K., Rajmohan, N. and Szpunar, J. A.: Influence of primary annealing condition on texture development in grain oriented electrical steel. Acta Mater. 50, 1825 (2002).Google Scholar