Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-23T11:01:17.139Z Has data issue: false hasContentIssue false
  • English
  • Français

The Creep Behaviors of Two Fine-grained XD TiAl Alloys Produced by Similar Heat Treatments

Published online by Cambridge University Press:  26 February 2011

Hanliang Zhu ,
Dongyi Seo ,
Kouichi Maruyama  and
Peter Au
Hanliang Zhu
Affiliation:
Graduate School of Environmental Studies, Tohoku University, Sendai 980–8579, Japan
Dongyi Seo
Affiliation:
Structures, Materials and Propulsion Laboratory, Institute for Aerospace Research, National Research Council of Canada, Ottawa, Ont., Canada K1A 0R6
Kouichi Maruyama
Affiliation:
Graduate School of Environmental Studies, Tohoku University, Sendai 980–8579, Japan
Peter Au
Affiliation:
Structures, Materials and Propulsion Laboratory, Institute for Aerospace Research, National Research Council of Canada, Ottawa, Ont., Canada K1A 0R6
Get access

Abstract

The microstructural characteristics and creep behavior of two fine-grained XD TiAl alloys, Ti-45Al and 47Al–2Nb–2Mn+0.8vol%TiB2 (at%), were investigated. A nearly lamellar structure (NL) and two kinds of fully lamellar (FL) structures in both alloys were prepared by selected heat treatments. The results of microstructural examination and tensile creep tests indicate that the 45XD alloy with a NL structure possesses an inferior creep resistance due to its coarse lamellar spacing and larger amount of equiaxed γ grains at the grain boundaries, whereas the same alloy in a FL condition with fine lamellar spacing lowers the minimum creep rates. Contrary to 45XD, the 47XD alloy with a NL structure exhibits the best creep resistance. However, 47XD with a FL structure with finer lamellar spacing shows inferior creep resistance. On the basis of microstructural deformation characteristics, it is suggested that the well-interlocked grain boundary and relatively coarse colony size in FL and NL 47XD inhibit sliding and microstructural degradation at the grain boundaries during creep deformation, resulting in better creep resistance. Therefore, good microstructural stability is essential for improving the creep resistance of these alloys.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 842: Symposium S – Integrative and Interdisciplinary Aspects of Intermetallics , 2004 , S5.50
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Hsiung, L. M., Nieh, T. G.: Mat. Sci. Eng. A364 (2004) 1–10 Google Scholar
[2] Seo, D.Y., Zhao, L., Beddoes, J.: Mat. Sci. Eng. A329–331 (2002) 130–140 Google Scholar
[3] Kim, H. Y., Maruyama, K.: Acta Mater. 51(2003) 2191–2204.Google Scholar
[4] Zhu, H., Seo, D.Y., Maruyama, K., Mat. Trans. 45(2004) 2618–2621 Google Scholar
[5] Maruyama, K., Yamamoto, R., Nakakuki, H., Fujitsuna, N.: Mat. Sci. Eng. A239–240 (1997) 419–428.Google Scholar
[6] Chakraborty, A., Earthman, J. C.. Met. Mat. Trans. 1997; 28A: 979.Google Scholar
[7] Chen, W. R., Triantafillou, J., Beddoes, J., Zhao, L.: Intermetallics 7(1999) 171–178.Google Scholar
[8] Zhu, H., Seo, D.Y., Maruyama, K., Au, P., Scripta Mat. 52(2005): 45–50.Google Scholar
[9] Yamamoto, R., Mizoguchi, K., Wegmann, G., Maruyama, K.: Intermetallics 6 (1998) 699–702 Google Scholar