Hostname: page-component-7bb8b95d7b-l4ctd Total loading time: 0 Render date: 2024-09-29T22:49:11.124Z Has data issue: false hasContentIssue false
  • English
  • Français

Annealing Effects On The Microstructure Of Electrodeposited Cu/Ag Multilayered Nanocomposites

Published online by Cambridge University Press:  10 February 2011

Dan Kong ,
Qing Zhai  and
Fereshteh Ebrahimi
Dan Kong
Affiliation:
Materials Science and Engineering Department University of Florida, Gainesville, FL 32611
Qing Zhai
Affiliation:
Materials Science and Engineering Department University of Florida, Gainesville, FL 32611
Fereshteh Ebrahimi
Affiliation:
Materials Science and Engineering Department University of Florida, Gainesville, FL 32611
Get access

Abstract

TEM was used to investigate the annealing effects on the microstructure of two electrodeposited Cu/Ag multilayered nanocomposites with bi-layer thickness values of 110nm and 330nm, respectively, as well as electrodeposited pure copper. It was found that silver layers limited the lateral growth of columnar copper grains and possibly acted as sites for nucleation of new copper grains in the as-deposited composites. The refinement of copper grains in this condition is one reason for the much higher strength of these materials in comparison to pure copper. Annealing at 100 °C did not change the microstructure significantly. After annealing at 150 °C, recrystallization occurred in all samples. The degree of recrystallization was dependent on the extent of internal stresses. Recrystallization was complete in the 110nm bi-layer thick composite, which had the highest internal stresses owning to its large Cu/Ag interfacial area. The recrystallization and growth of copper grains can be one reason for the drastic drop of the composites yield strength after annealing at 150°C

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 505 , 1997 , 457
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Tench, D. M. and White, J.T., in Micocomposites and Nanophase Materials, edited by Van Aken, David C., Was, G. S. and Ghosh, A. K., TMS publication, PA, p. 53 (1991).Google Scholar
2.Ruff, A. W. and Lashmore, D. S., Wear, 151, p. 245 (1991).Google Scholar
3.Bird, K. D. and Schlesinger, M., J. Electrochem. Soc., 142 (4), p. L65 (1995).Google Scholar
4.Wang, L., Fricoteaux, P., Yu-Zhang, K., Troyon, M., Bonhomme, P., Douglade, J., and Metrot, A., Thin Solid Films, 261, p. 160 (1995).Google Scholar
5.Zhai, Q., Kong, D., Morrone, A., and Ebrahimi, F., MRS Proc., 451, p. 489 (1997).Google Scholar
6.Zhai, Q., Kong, D., and Ebrahimi, F., “Mechanical Properties of Cu/Ag Multilayered Composites”, submitted to Mater. Sci. Engng., 1997.Google Scholar
7.Ebrahimi, F., Zhai, Q., D. Kong,“ Characteriztion of Cu/Ag Multilayered Structures Produced by Electrodeposition”, submitted to Metall. Trans., 1997.Google Scholar
8.Schultze, W. A., J.Crystal Growth, 13/14, p. 421 (1972).Google Scholar
9.Merchant, H. D., Defect Structure Morphology and Properties of Deposites, edited by Merchant, H., TMS Publication, PA, p. 1 (1995).Google Scholar
10.Hu, H., Recovery and Recrystallization of Metals, edited by Himmel, , AIME Conference Series, Interscience Publishers, New York, p. 311 (1963)Google Scholar