Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-19T03:44:49.970Z Has data issue: false hasContentIssue false
  • English
  • Français

Amorphous calcium phosphate nano-powders made from radio frequency (RF) plasma spraying

Published online by Cambridge University Press:  15 February 2011

Xu Jinling ,
Rajendra Kumar ,
K.A. Khor  and
P. Cheang
Xu Jinling
Affiliation:
Advanced Materials Research Centre (AMRC), Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
Rajendra Kumar
Affiliation:
Advanced Materials Research Centre (AMRC), Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
K.A. Khor
Affiliation:
Advanced Materials Research Centre (AMRC), Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
P. Cheang
Affiliation:
Advanced Materials Research Centre (AMRC), Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
Get access

Abstract

Predominantly amorphous nano powders of calcium phosphate were produced by radio frequency (RF) plasma and subsequently characterised by SEM, TEM and XRD. Quantitative phase analysis was carried out by the Rietveld method. The starting feedstock was comprised of hydroxyapatite (HA) powders spray dried from a suspension. The input parameters were varied to produce predominantly amorphous calcium phosphate powders. Results showed that as the plate power was increased and the flow rate of feedstock was decreased the as-sprayed powders produced were predominantly amorphous. The average particle size of the powders was about 20-40 nm, depending on process parameters, as confirmed by TEM observation. These powders are thought to have excellent bio-resorbability and are targetted for use in gene and drug delivery technologies. These nano-sized powders are also envisioned to enhance the mechanical properties of bulk products sintered by appropriate techniques.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 777: Symposium A – Nanostructuring Materials with Energetic Beams , 2003 , T9.1
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Babat, G.I., J. Inst. Elect. Engr. 94, 27 (1974).Google Scholar
2. Reed, T.B., J. Appl. Phy. 32, 821 (1961).Google Scholar
3. Bouyer, E., Gitzhofer, F. and Boulos, M.I., IEEE Trans. Mat. Sci. 25, 1066 (1997).Google Scholar
4. Park, J.B., Lakes, R.S., Biomaterials: An introduction, 2 nd edition, New York, Plenum press (1992).Google Scholar
5. Bajpai, P.K., Billote, W.G., Biomedical engineering handbook, CRD press (1995).Google Scholar
6. Radin, S.R., Ducheyne, P., J. Mat. Sci.: Mat. Med. 3, 33 (1992).Google Scholar
7. Osaka, J. Minara, Takenchi, K., Asada, M. and Takahashi, K., J. Mat. Sci.: Mat. Med. 2, 51 (1991).Google Scholar
8. Kumar, R., Cheang, P. and Khor, K.A., J. Mat. Proc. Tech., 113, 456 (2001).Google Scholar
9. Knowles, J.C, Gross, K., Berndt, C.C. and Bonfield, W., Bioceramics 8, 311 (1997).Google Scholar
10. Kumar, R., Cheang, P., Khor, K.A., Int. Thermal Spray Conf. (ITSC), Singapore (2001).Google Scholar
11. Kumar, Rajendra, RF processing of ultra-fine bio-ceramic materials, PhD Thesis, Nanyang Technological University, 2002.Google Scholar
12. Gross, K.A. Gross, V. and Berndt, C.C., J. Am. Ceram. Soc., 81, 106 (1998).Google Scholar
13. Khor, K.A., Kumar, R. and Cheang, P., Int. Conf. Metallurgical Coatings and Thin Films (ICMCTF), San Diego (2003).Google Scholar