Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-19T06:31:30.437Z Has data issue: false hasContentIssue false
  • English
  • Français

Toughening Mechanisms in Intermetallic γ-TiAl Alloys Containing Ductile Phases

Published online by Cambridge University Press:  22 February 2011

C. K. Elliott ,
G. R. Odette ,
G. E. Lucas  and
J. W. Sheckherd
C. K. Elliott
Affiliation:
Department of Materials, University of California, Santa Barbara, CA 93106
G. R. Odette
Affiliation:
Department of Materials, University of California, Santa Barbara, CA 93106
G. E. Lucas
Affiliation:
Department of Materials, University of California, Santa Barbara, CA 93106
J. W. Sheckherd
Affiliation:
Department of Materials, University of California, Santa Barbara, CA 93106
Get access

Abstract

This work is aimed at developing understanding of ductile phase toughening in powder-processed intermetallic γ-TiAl alloys. The nominally ductile phases studied include Nb and Ti6Al4V, in the form of pancake shaped particles. Toughening is primarily due to the formation of crack face bridging zones. Toughness increases in the composites with a Ti6Al4V phase are limited due to particle embrittlement during processing. In this case, toughening is associated with the formation of short, low ductility/high strength bridge zones. Larger toughness increases and significant resistance curves are observed in composites containing Nb particles. In this case, long, high ductility/low strength bridge zones are observed. The behavior of the Nb composites is consistent with current understanding of constrained deformation of embedded particles and bridge zone toughening models. Additional toughening was observed in the Nb composites due to crack deflection and blunting in orientations where the crack intersects the broad pancake face.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 120: Symposium G – High-Temperature/High-Performance Composites , 1988 , 95
Copyright
Copyright © Materials Research Society 1988

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Krstic, V. D., Nicholson, P. S. and Hoagland, R. G., J. Am. Ceram. Soc., 64, pp. 499–504 (1981).Google Scholar
2. Sigl, L. S., Mataga, P., Dalgleish, B. J., McMeeking, R. M. and Evans, A. G., 1987 (in press).Google Scholar
3. SigI, L. S. and Exner, H. E., Met Trans. A, 18A, pp. 1299–1308 (1987).Google Scholar
4. Budiansky, B., Amazigo, J. C. and Evans, A. G., (AD-A183 208/8/GAR, Harvard University, 1987) p. 34.Google Scholar
5. Rose, L. R. F., J. Mech. Phys. Solids, 34, (6), pp. 609–616 (1986).Google Scholar
6. ASTM E399-83 Plane-Strain Fracture Toughness of Metallic Materials, 1985 Annual Book of ASTM Standards (ASTM, Philadelphia, 1983).Google Scholar
7. Tabor, D., Hardness of Metal, (Clarenden Press, London, 1951).Google Scholar
8. Tada, H., Paris, P C., Irwin, G. R., The Stress Analysis of Cracks Handbook, (Del Research, St. Louis, MO, 1985).Google Scholar
9. Eberhart, J. and Ashby, M. F., Cambridge University Engineering Dept. Report, (CUED/C-MATS/TR 140, Cambridge University, 1987).Google Scholar