Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-23T08:49:54.314Z Has data issue: false hasContentIssue false
  • English
  • Français

Thermoelectric Properties of Tl2Te-Sb2Te3 Pseudo-Binary System

Published online by Cambridge University Press:  01 February 2011

Ken Kurisaki ,
Keita Goto ,
Atsuko Kosuga ,
Hiroaki Muta  and
Shinsuke Yamanaka
Ken Kurisaki
Affiliation:
[email protected]
Keita Goto
Affiliation:
[email protected], Osaka University, Division of Sustainable Energy and Environmental Engineering, Japan
Atsuko Kosuga
Affiliation:
[email protected]
Hiroaki Muta
Affiliation:
[email protected]
Shinsuke Yamanaka
Affiliation:
[email protected]
Get access

Abstract

Polycrystalline-sintered samples of thallium based substances, (Tl2Te)100−x(Sb2Te3)x (x= 0, 1, 5, 10), were prepared by melting Tl2Te and Sb2Te3 ingots followed by annealing in sealed quartz ampoules. The thermoelectric properties were measured from room temperature to around 600 K. The values of the Seebeck coefficient of all samples are positive, indicating a p-type conduction characteristic. The maximum value of the power factor is 6.53×10−4 Wm−1K−2 at 591 K obtained for x= 10 (Tl9SbTe6), which is about one order lower than those of state-of-the-art thermoelectric materials. All samples indicate an extremely low thermal conductivity, for example that of Tl2Te is approximately 0.35 Wm−1K−1 from room temperature to around 600 K. Although the electrical performance of the samples is not so good, the ZT value is relatively high due to the extremely low thermal conductivity. The maximum ZT value is 0.42 at 591 K obtained for Tl9SbTe6.

Keywords

thermoelectricitythermal conductivityTl
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 886: Symposium F – Materials and Technologies fore Direct Thermal-to-Electric Energy Conversion , 2005 , 0886-F08-03
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Sharp, J. W., Sales, B. C., Mandrus, D., Chakoumakos, B. C., Appl. Phys. Lett. 74, 3794 (1999).Google Scholar
2. Wolfing, B., Kloc, C., Teubner, J., Bucher, E., Phys. Rev. Lett. 86, 4350 (2001).Google Scholar
3. Sales, B. C., Chakoumakos, B. C., Mandrus, D., Phys. Rev. B 61, 2475 (2000).Google Scholar
4. Kurosaki, K., Uneda, H., Muta, H., Yamanaka, S., J. Alloys Compd. 395, 304 (2005).Google Scholar
5. Kurosaki, K., Kosuga, A., Muta, H., Uno, M., Yamanaka, S., Appl. Phys. Lett. 87, 061919 (2005).Google Scholar
6. Kurosaki, K., Goto, K., Kosuga, A., Muta, H., Uno, M., Yamanaka, S., Mater. Trans. to be submitted.Google Scholar
7. Yamanaka, S., Kosuga, A., Kurosaki, K., J. Alloys Compd. 352, 275 (2003).Google Scholar
8. Kurosaki, K., Uneda, H., Muta, H., Yamanaka, S., J. Alloys Compd. 376, 43 (2004).Google Scholar
9. Gawel, W., Fuglewicz, B., Zaleska, E., Polish Journal of Chemistry 63, 93 (1989).Google Scholar
10. Barua, K. C., Goswami, A., Surface Science 14, 415 (1969)Google Scholar
11. Voroshilov, Yu. V., Gurzan, M. I., Kish, Z. Z., Lada, L. V., Inorganic Materials 24, 1265 (1988).Google Scholar