Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-29T08:11:57.179Z Has data issue: false hasContentIssue false
  • English
  • Français

Surface Modifaction of Ultra High Molecular Weight Polyethylene by Low Energy DC Plasma Discharge

Published online by Cambridge University Press:  10 February 2011

M. S. Hargreaves ,
D. S. Hussey  and
R. E. Leuchtner
M. S. Hargreaves
Affiliation:
University of New Hampshire Department of Physics, Demeritt Hall, Durham, NH 03824
D. S. Hussey
Affiliation:
University of New Hampshire Department of Physics, Demeritt Hall, Durham, NH 03824
R. E. Leuchtner
Affiliation:
University of New Hampshire Department of Physics, Demeritt Hall, Durham, NH 03824
Get access

Abstract

Surface effects produced by plasma processing Ultra High Molecular Weight polyethylene (UHMW) were examined. The goal was to enhance adhesion of UHMW to a variety of polar polymers. This research focussed on enhancing adhesion to polyurethane. UHMW samples were immersed in a DC discharge and subjected to various processing conditions. The background gases experimented with were oxygen, nitrogen, and argon, and the pressure was varied between 6-67 Pa. The processing time, discharge current and discharge potential were also varied. A polar polymer (polyurethane) was subsequently applied to the processed UHMW samples and the tensile strength of the bonds was measured. Standard dogbone specimens were fabricated, and the polymer interfaces placed in the middle of the gage section and oriented normal to the tensile axis. The specimens were tested to failure in displacement control at an approximate strain rate of 0.2% per sec. In general, significant enhancement in yield strength was observed over unprocessed samples, where essentially no bonding occurred. Samples subjected to plasma processing in oxygen showed the strongest adhesion, while those in argon were almost as good, followed by nitrogen.

The contact angle of water on the processed UHMW samples ranged from about 45° to less than 2°, while unprocessed samples had a contact angle of about 70°. These data correlated with the yield tests. XPS was used to examine the composition of the UHMW surfaces before and after plasma processing with oxygen. It is believed that the plasma etched off surface layers, creating unsaturated carbon bonds that can chemically react with polar polymer groups. Precast, processed UItMW surfaces were found to be reactive for periods of up to one week. Optimum conditions of plasma processing were identified, and will be discussed in light of the chemistry occurring at the interface.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 544: Symposium Y – Plasma Deposition and Treatment of Polymers , 1998 , 291
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1- see, e.g., “Plasma Polymerization”, chap. 4 in Plasma Science and Technology, Boenig, H. V., Cornell University Press, Ithaca, NY (1982).Google Scholar
2- Yeddonapalli, L. M., J. Chem. Phys. 10, 249(1942).Google Scholar
3- Kobyashi, H., Shem, M., and Bell, A. T. T. Res. Contract, AD - 762, 480, ONR (15 June 1973).Google Scholar
4- Zisman, W. A., Chap. 1, in Contact Angle: Wettability and Adhesion, Advances in Chemistry Series 43, Robert, Gould, editor, American Chemical Society, Washington, DC, 1964.Google Scholar
5- Properties of Plastic Resins and Compounds, chap. 6 in Marks' Standard Handbook for Mechanical Engineers, Avallone, E. A., Baumeister, J. III, editors, McGraw-Hill, NY, pp. 197 (1996).Google Scholar
6- Andur 2-95AP Prepolymer Data Sheet, Anderson Development Company, Bulletin #012084, Adrian, MI, 49221.Google Scholar