Hostname: page-component-586b7cd67f-l7hp2 Total loading time: 0 Render date: 2024-11-29T10:06:35.487Z Has data issue: false hasContentIssue false
  • English
  • Français

Structural Characterization of Oxide layers on Aluminum Formed by Exposure to Hyperthermal Atomic Oxygen

Published online by Cambridge University Press:  01 February 2011

Long Li ,
Liang Wang ,
Timothy K. Minton  and
Judith C. Yang
Long Li
Affiliation:
Materials Science and Engineering Department University of Pittsburgh, Pittsburgh, PA., USA
Liang Wang
Affiliation:
Materials Science and Engineering Department University of Pittsburgh, Pittsburgh, PA., USA
Timothy K. Minton
Affiliation:
Department of Chemistry and Biochemistry, Montana State University, Bozeman, MT., USA
Judith C. Yang
Affiliation:
Materials Science and Engineering Department University of Pittsburgh, Pittsburgh, PA., USA
Get access

Abstract

Single crystal Al (100) was exposed to 5 eV atomic oxygen beam. The sample was maintained at a temperature of 220°C and the total atomic oxygen fluence was 8×1019 atom.cm-2. We have characterized the resulting oxide and interface structures by cross-sectional (scanning) transmission electron microscopy ((S)TEM) and scanning electron microscope(SEM). Our TEM results show that an amorphous aluminum oxide layer with ∼6 nm thickness formed on the aluminum crystal, and a rough alumina/Al(100) interface forms. For a systematic study of the evolution of the oxide, a unique Physical Sciences, Inc. Pitt FASTTM AO laser detonation atomic oxygen source in a UHV chamber is employed. The system is equipped with a Maxtek RQCMTM system, a research quartz crystal microbalance (QCM) with a dual-sensor head, to dynamically measure the mass change of an aluminum film coated on the sensor crystal during exposure to atomic oxygen. The Al film initially experiences mass loss, and then parabolic mass gain. To observe the structural evolution of the oxide, a very thin Al (100) single crystal was exposed inside the AO source, characterized by SEM and TEM. The surface morphology changed from flat to rough after 5.5 minutes of exposure. This surface roughening could be related to the initial mass loss measured by QCM.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 851: Symposium NN – Materials for Space Applications , 2004 , NN9.4
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hedin, A. E., J. Geophys. Res. 92(5), 4649 (1987).Google Scholar
2. Reddy, M. R., J. Mater. Sci. 30, 281 (1995).Google Scholar
3. Chambers, A. R., Harris, I. L. and Roberts, G. T., Mater. Lett. 26, 121 (1996).Google Scholar
4. Miller, G. P., Pettigrew, P. J., Raikar, G. N. and Gregory, J. C., Rev. Sci. Instrm. 68(9), 3557(1997).Google Scholar
5. Harris, I. L., Chambers, A. R. and Roberts, G. T., Mater. Lett. 31, 321 (1997).Google Scholar
6. Yang, J. C. et al to be published.Google Scholar
7. Adegboyega, G. A., Journal de Physique III 2 (9), 1749 (1992).Google Scholar
8. Kuznetsova, A., Yates, J. T. Jr, Zhou, G. et al., Langmuir 17 (7), 2146 (2001).Google Scholar
9. Popova, I., Zhukov, V., and Yates, J. T. Jr,Physical Review Letters 89 (27), 276101 (2002)Google Scholar
10. Oakes, D. B., Krech, R. H., Upschulte, B. L. et al., Journal of Applied Physics 77 (5), 2166 (1995).Google Scholar