Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-25T18:29:23.515Z Has data issue: false hasContentIssue false
  • English
  • Français

Stress Relaxation in Al-Si-Cu Thin Films and Lines

Published online by Cambridge University Press:  21 February 2011

A. Witvrouw ,
J. Proost ,
B. Deweerdt ,
Ph. Roussel  and
K. Maex
A. Witvrouw
Affiliation:
IMEC, Kapeldreef 75, 3001 Leuven, Belgium
J. Proost
Affiliation:
IMEC, Kapeldreef 75, 3001 Leuven, Belgium
B. Deweerdt
Affiliation:
IMEC, Kapeldreef 75, 3001 Leuven, Belgium
Ph. Roussel
Affiliation:
IMEC, Kapeldreef 75, 3001 Leuven, Belgium
K. Maex
Affiliation:
IMEC, Kapeldreef 75, 3001 Leuven, Belgium
Get access

Abstract

Substrate curvature measurements were used to study stress relaxation in Al-Si-Cu films at temperatures between 45 and 165 °C. Dislocation glide with an average activation energy, resp. athermal flow stress of 1.7 ± 0.2 eV, resp. 600 ± 200 MPa could describe the relaxation data for temperatures up to 120 °C well. Stress relaxation at 92 °C was found to progress much slower in 1 μm wide nitride passivated lines than in thin films or unpassivated lines.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 356: Symposium B2 – Thin Films: Stresses and Mechanical Properties V , 1994 , 441
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Smith, J. F. and Wagner, I., Advanced Aluminum Metallization. Part I: Aluminum Thin Film Properties, (1991 MRC Thin Film School), 2.Google Scholar
[2] d’Heurle, F.M. and Ho, P.S. in Thin Films: Interdiffusion and Reactions, ed. by Poate, J., Tu, K. and Mayer, J. (N.Y.), 293 (1978).Google Scholar
[3] Okabayashi, H., Mat. Sci. Eng. R11 (5), 191–241 (1993).Google Scholar
[4] Volkert, C.A., Alofs, C.F. and Liefting, J.R., J. Mater. Res. 9 (5), 1147 (1994).Google Scholar
[5] Nix, W.D., Metall. Trans A 20A, 3317 (1989).Google Scholar
[6] Gardner, D.S. and Flinn, P.A., IEEE Trans, on El. Dev. 35 (12), 2160 (1988).Google Scholar
[7] Frost, H.J. and Ashby, M.F. in Deformation Mechanism Maps (Pergamon Press, Oxford, 1982), Chapter 2.Google Scholar
[8] Mechanical behavior of Materials, ed. by Clintock, F.A. and Argon, A.S. (Addison-Wesley Company, Reading, 1966), 276–281.Google Scholar
[9] Aluminum. Properties and Physical Metallurgy, ed. by Hatch, J.E. (ASM, Metal Parks, Ohio), 47 (1984).Google Scholar
[10] Clarke, G.M. in Statistics and Experimental Design. 2nd edition (Edward Arnold Ltd.), 104 (1980).Google Scholar
[11] Hull, D. and Bacon, D.J., Introduction to Dislocations. 3th edition (Pergamon Press, Oxford, NY), 242 (1984).Google Scholar
[12] Hosoda, T., Niwa, H., Yagi, H. and Tsuchikawa, H., Proc. 1991 IRPS (IEEE), 77 (1991).Google Scholar