Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-29T07:39:58.729Z Has data issue: false hasContentIssue false
  • English
  • Français

The Solidification Microstructure of Ai-Cu-Si Alloys Metal Matrix Composites

Published online by Cambridge University Press:  10 February 2011

O. Garbellini ,
H. Palacio  and
H. Biloni
O. Garbellini
Affiliation:
IFIMAT-CIC,UNICEN. Pinto 399 (7000) Tandil, Argentina, [email protected]
H. Palacio
Affiliation:
IFIMAT-CIC,UNICEN. Pinto 399 (7000) Tandil, Argentina, [email protected]
H. Biloni
Affiliation:
LEMIT-CIC, Calle 52 entre 121 y 122, (1900) La Plata, Argentina, [email protected]
Get access

Abstract

The relationship between solidification microstructure and fluidity in MMC was studied. The composites were fabricated by infiltration of liquid metal into a alumina SAFFIL fibers preform under a gas pressure, using alloys of the AlCuSi system as matrices. The fluidity was measured in terms of classic foundry practice (i.e., the distance of flow liquid metal into the preform, while solidifying). The characterization of solidification microstructure in the cast composite was analysed and correlated with the results of fluidity. The attention was particularly focused on such effects as the presence or absence of selective nucleation, the refinement of certain solidifying phases in the presence of fibers and their influence on microstructure formation and segregation of certain elements present in the liquid at the fiber matrix interface. By comparing reinforced and non reinforced zones, it was shown that the presence of fibers resulted in a refinement of the dendritic arm spacing of the α-Al phase, with nucleation of Si on the fibers and without nucleation of primary Al dendrites. The results were discussed and compared with the microstructures and fluidity test of the unreinforced Al-Cu-Si alloys.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 481: Symposium P – Science and Technology of Semiconductor Surface Preparation , 1997 , 77
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Garbellini, O., Palacio, H. and Biloni, H., Cast Metals, 3, p 82 (1990).Google Scholar
2. Mortensen, A., Masur, L.J., Cornie, J.A., and Flemings, M.C., Metall. Trans., 20A, p 2549 (1989).Google Scholar
3. Mortensen, A., Masur, L.J., Cornie, J.A., and Flemings, M.C., Metall. Trans., 20A, p 2535 (1989).Google Scholar
4. Fukunaga, H. and Goda, K., J. Japan. Inst. Metals, 49, p 78 (1985).Google Scholar
5. Nourbakhsh, S., Liang, F.L., and Margolin, H., Metall. Trans. A, 20A, p 1861 (1989).Google Scholar
6. Mortensen, A., Cornie, J.A. and Flemings, M.C., J.Met., 40, p 12 (1988).Google Scholar
7. Clyne, T.W., Bader, M.G., Cappleman, G.R., and Hubert, P.A., J.Mater. Sci., 20, p 85 (1985).Google Scholar
8. Long, S., Zhang, Z. and Flower, H.M., Acta metall.mater., 42, p 1389 (1994).Google Scholar
9. Garbellini, O., Palacio, H. and Biloni, H., to be published.Google Scholar
10. Campbell, J., Cast Metals, 4, p 101 (1991).Google Scholar
11. Mortensen, M.A. and Flemings, M.C., Metall. Trans., 27A, p 595 (1996).Google Scholar
12. Campbell, J. in Castings, edited by Butterworth-Heinemann Ltd., Oxford, U.K., 1991.Google Scholar