Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-19T10:16:03.767Z Has data issue: false hasContentIssue false
  • English
  • Français

Room Temperature Tensile Ductility in Powder Processed B2 FeAi Alloys

Published online by Cambridge University Press:  28 February 2011

M. A. Crimp ,
K. M. Vedula  and
D. J. Gaydosh
M. A. Crimp
Affiliation:
Department of Metallurgy and Materials Science, Case Western Reserve University, Cleveland, Ohio 44106
K. M. Vedula
Affiliation:
Department of Metallurgy and Materials Science, Case Western Reserve University, Cleveland, Ohio 44106
D. J. Gaydosh
Affiliation:
NASA Lewis Research Center, Cleveland, Ohio 44135
Get access

Abstract

It has been shown that it is possible to obtain significant room temperature tensile ductility in FeAl alloys using iron-rich deviations from stoichiometry. A comparison of the room temperature tensile and compressive behaviors of Fe−50at% Al and Fe−40at% Al shows that FeAl is brittle at higher Al contents because it fractures along grain boundaries before general yielding. Lower aluminium contents reduce the yield stress substantially and hence some ductility is observed before fracture.

Addition of boron results in measurable improvements in ductility of Fe−40at% Al and is accompanied by an increase in transgranular tearing on the fracture surface, suggesting a grain boundary strengthening mechanism.

Increasing the cooling rate following annealing at 1273 K results in a large increase in the yield strength and a corresponding decrease in ductility.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 81: Symposium H – High-Temperature Ordered Intermetallic Alloys II , 1986 , 499
Copyright
Copyright © Materials Research Society 1987

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Stephens, J. R., Materials Research Society Symposia Proceedings, edited by Koch, C. C., Liu, C. T., and Stoloff, N. S. (MRS Publishers, Pittsburgh) 39 381 (1985).Google Scholar
2. Umakoshi, Y. and Yamaguchi, M., Phil. Mag. A, 44 (3), 711(1981).Google Scholar
3. Yamagata, T. and Yoshida, H., Mat. Sci. and Eng., 12 95 (1973).Google Scholar
4. Johnson, T. L., Davies, R. G., and Stoloff, N. S., Phil. Mag., 12 305 (1965).CrossRefGoogle Scholar
5. Liu, C. T., White, C. L., and Horton, J. A., Acta Met., 33 (2), 213(1985).CrossRefGoogle Scholar
6. Ogura, T., Masumoto, S. Hanada and Izumi, O., Met. Trans.-A, 16 441 (1985).Google Scholar
7. Choudhury, A., White, C. L., and Brooks, C. R., Submitted to Tripta Met.Google Scholar
8. Crimp, M. A., and Vedula, K., Mat. Sci. and Eng., 78 193 (1986).Google Scholar
9. Gaydosh, D. J. and Crimp, M. A., Materials ResearcF-Society Sympoosia Proceedings, edited by Koch, C. C., Liu, C. T., and Stoloff, N. S. (MRS Publishers, Pittsburgh) 39 429 (1985).Google Scholar
10. Westbrook, J. H., J. Electro. Chem. Soc., 103 54 (1956).Google Scholar
11. Vedula, K. M., 1986 MRS Symposium on High-TTemperature Ordered Intermetallic lloys.Google Scholar
12. Crawford, R. C., and Ray, I. L. F., Phil. Mag., 35 (3) 549(1977).Google Scholar
13. Crawford, R. C., Phil. Mag., 35 (3) 567(1977).Google Scholar
14. Stoloff, N. S. and Davies, R. G., Acta Met., 12 473 (1964).Google Scholar
15. Brown, N., Acta Met., 7 210 (1959).Google Scholar
16. Fourdeux, A. and Lesbats, P., Phil. Mag. A, 45 81 (1982).CrossRefGoogle Scholar