Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-20T05:14:30.584Z Has data issue: false hasContentIssue false
  • English
  • Français

Micro-Molded High Q Polymer Resonators for Optical Loss Determination

Published online by Cambridge University Press:  01 February 2011

Andrea L. Martin ,
Akil Srinivasan ,
Deniz K. Armani ,
Bumki Min  and
Kerry J. Vahala
Andrea L. Martin
Affiliation:
Department of Applied Physics, California Institute of Technology, 1200 E California Blvd, M/C 128-95 Pasadena, CA 91125, U. S. A.
Akil Srinivasan
Affiliation:
Department of Applied Physics, California Institute of Technology, 1200 E California Blvd, M/C 128-95 Pasadena, CA 91125, U. S. A.
Deniz K. Armani
Affiliation:
Department of Applied Physics, California Institute of Technology, 1200 E California Blvd, M/C 128-95 Pasadena, CA 91125, U. S. A.
Bumki Min
Affiliation:
Department of Applied Physics, California Institute of Technology, 1200 E California Blvd, M/C 128-95 Pasadena, CA 91125, U. S. A.
Kerry J. Vahala
Affiliation:
Department of Applied Physics, California Institute of Technology, 1200 E California Blvd, M/C 128-95 Pasadena, CA 91125, U. S. A.
Get access

Abstract

Replica molding of ultra-high-Q toroidal microresonators can produce polymer microresonators with material-limited quality factors (Q). This was demonstrated previously using polymers which cure thermally. In this work, high Q polymer microresonators were fabricated using the replica molding technique from previously uncharacterized polymers which require either a thermal or UV cure. The quality factor and effective refractive index of whispering gallery modes was measured at wavelengths ranging from the visible (680nm) through the near-IR (1550nm). The optical absorption coefficient (material absorption) of these previously uncharacterized polymers was determined from the quality factor and effective refractive index of the polymer.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 872: Symposium J – Micro- and Nanosystems—Materials and Devices , 2005 , J8.1
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Poon, J. K., Huang, Y.Y., Paloczi, G. T., and Yariv, A., Soft lithography replica molding of critically coupled polymer microring resonators, IEEE Photonics Tech. Lett. 16 2496 (2004).Google Scholar
2 Kim, J-S., Kang, J-W., and Kim, J-J., Simple and Low Cost Fabrication of Thermally Stable Polymeric Multimode Waveguides using a UV-curable Epoxy. Jpn. J. Appl. Phys. 42 1277 2003.Google Scholar
3 Martin, A. L., Armani, D. K., Yang, L., and Vahala, K. J., Replica-molded high-Q polymer microresonators. Opt. Lett. 29 533 (2004).Google Scholar
4 Armani, D. K., Kippenberg, T. J., Spillane, S. M., and Vahala, K. J., Ultra-high-Q toroid microcavity on a chip. Nature 421 925 (2003).Google Scholar
5 Knight, J. C., Cheung, G., Jacques, F., and Birks, T. A., Phase-matched excitation of whispering-gallery-mode resonances by a fiber taper. Opt. Lett. 22 1129 (1997).Google Scholar
6 Cai, M., Painter, O. J., and Vahala, K. J., Observation of critical coupling in a fiber taper to a silica-microsphere whispering-gallery mode system. Phys. Rev. Lett. 85 74 (2000).Google Scholar
7 Spillane, S. M., Kippenberg, T. J., Painter, O. J., and Vahala, K. J., Ideality in a fiber-taper-coupled microresonator system for application to cavity quantum electrodynamics. Phys. Rev. Lett. 91 043092 (2003).Google Scholar
8 Gorodetsky, M. L., Savchenkov, A. A., and Ilchenko, V. S., Ultimate Q of optical microsphere resonators. Opt. Lett. 21 453 (1996).Google Scholar