Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-09T14:57:39.087Z Has data issue: false hasContentIssue false
  • English
  • Français

Ion Implantation into High-Speed Steel for Improved Tribology

Published online by Cambridge University Press:  22 February 2011

J-P. Hirvonen ,
D. Rück ,
S. Yan ,
R. Lappalainen  and
P. Torri
J-P. Hirvonen
Affiliation:
Technical Research Centre of Finland, Metallurgy Laboratory, FIN-02151 Espoo, Finland
D. Rück
Affiliation:
Gesellschaft für Schwerionenforschung mbH, D-6100 Darmstadt, Germany
S. Yan
Affiliation:
Gesellschaft für Schwerionenforschung mbH, D-6100 Darmstadt, Germany
R. Lappalainen
Affiliation:
Department of Physics, FIN-00014 University of Helsinki, Finland
P. Torri
Affiliation:
Department of Physics, FIN-00014 University of Helsinki, Finland
Get access

Abstract

Ion implantation into steels with a martensitic microstracture is reviewed and discussed in terms of different implanted species and observed changes in the structure. Both single ion and dual ion implantation treatment are included. The disability of the nitrogen ion implantation to improve the tribological characteristics of steels with a martensitic microstructure can be overcome by dual implantation of titanium and carbon, for example. Results of tribological tests on samples in which titanium is replaced by chromium are more controversial, although changes in the sliding characteristics were observed. Dry sliding on the samples implanted up to 1018 ions/cm2 is totally different by nature and -based on the reported results- associated with the formation of carbon precipitates on the surface. The thermal stability of implanted nitrogen and carbon in MЗ high-speed steel was examined and nitrogen was shown to be less stable than carbon. Mechanical and tribological properties were further changed by heat treatment after ion implantation, which indicates that temperature is also a critical parameter during ion implantation.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 316: Symposium A – Materials Synthesis and Processing Using Ion Beams , 1993 , 507
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Metals Handbook, 9th edition, vol. 3 (American Society for Metals, Metals Park, OH, 1980) p. 421.Google Scholar
2 Kasak, A. and Neumeyer, T.A., Wear 14, 445 (1969).Google Scholar
3 Hedenqvist, P., Olsson, M.,and Söderberg, S., Surface Engineering 5 141 (1989).Google Scholar
4 Varjoranta, T., Hirvonen, J-P., and Anttila, A., Thin Solid Films 75 241 (1981).Google Scholar
5 Oliver, W.C., Hutchings, R., and Pethica, J.B., Met. Transactions 15A 2221 (1984).Google Scholar
6 Pope, L.E., Yost, F.G., Follstaedt, D.M., Picraux, S.T., and Knapp, J.A., Mat. Res. Soc. Symp. Proc. 27 661 (1984).Google Scholar
7 Carosella, C.A., Singer, I.L., Bowers, R.C., and Gossett, C.M., in Ion Implantation Metallurgy, eds. Preece, C.M. and Hirvonen, J.K. (AIME, Warrendale, PA, 1980) p. 103.Google Scholar
8 Cohen, M., Trans. Met. Soc. AIME 224 638 (1962).Google Scholar
9 Hirvonen, J-P., Nastasi, M., Jervis, T.R., and Zocco, T.G., The 7th International Conference on Ion Beam Modification of Materials, Knoxville, TN,USA, 9–14 September 1990, to be published.Google Scholar
10 Stræde, C.A., Poulsen, J.R., Lund, B.M., and Sørensen, G., Mat. Sci.Eng. A139 150 (1990).Google Scholar
11 Kobs, K., Dimigen, H., Denissen, C.J.M., Gerritsen, E., Politiek, J., Oechsner, R., Kluge, A.,and Ryssel, H., Nucl. Inst. Meth. B59/60 746 (1991).Google Scholar
12 Mikkelsen, N.J., Eskildsen, S.S., and Stræde, C.A., The 8th International Conference on Surface Modification of Metals by Ion Beams, Kanazawa, Japan, 13–17. September 1993, to be published in Surface and Coatings Technology.Google Scholar
13 Singer, I.L., Mat. Res. Soc. Symp. Proc. 27 102 (1984).Google Scholar
14 Follstaedt, D.M., Knapp, J.A., and Pope, L.E., Mat. Res. Soc.Symp.Proc. 140 133 (1989).Google Scholar
15 Hirvonen, J-P., Nastasi, M., Jervis, T.R., and Zocco, T.G., J. Appl.Phys. 67 7292 (1990).Google Scholar
16 Hirvonen, J-P., Nastasi, M., Jervis, T.R., and Zocco, T.G., Surface and Coatings Technology 43/44 7292 (1990).Google Scholar
17 Follstaedt, D.M., Knapp, J.A., Pope, L.E., and Picraux, S.T., Nucl. Inst. Meth. B12 359 (1985).Google Scholar
18 Hirvonen, J-P., Nastasi, M., Jervis, T.R., and Zocco, T.G., App.Phys.Lett. 51 232 (1987).Google Scholar
19 Alonso, F., Viviente, J.L., Oñate, J.I., Torp, B., and Nielsen, B.R., Nucl. Inst. Met. B80/81 (1993).Google Scholar
20 Langguth, K. and Ryssel, H., Wear 161 127 (1993).Google Scholar
21 Rück, D. et al. . Nucl. Tracks Radiat. Meas. 19 951 (1991).Google Scholar
22 Deconnick, G., Introduction to Radioanalytical Physics (Akademiai Kiado, Budabest, 1978) p. 229.Google Scholar
23 Lappalainen, R., Phys. Rev. B34 3076 (1986).Google Scholar
24 Hirvonen, J-P., Lappalainen, R., Koskinen, J., Anttila, A., Jervis, T.R., and Trkula, M., J. Mat. Res. 5 2524 (1990).Google Scholar
25 Follstaedt, D.M., Knapp, J.A., and Pope, L.E., J. Appl. Phys. 66 2743 (1989).Google Scholar