Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-29T09:41:27.050Z Has data issue: false hasContentIssue false
  • English
  • Français

Integrated Processinyg of Silicided Shallow Junctions using Rapid Thermal Annealing Prior to Dopant Activation

Published online by Cambridge University Press:  25 February 2011

Leonard Rubin ,
Nicole Herbots ,
JoAnne Gutierrez ,
David Hoffman  and
Di Ma
Leonard Rubin
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139
Nicole Herbots
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139
JoAnne Gutierrez
Affiliation:
Department of Electrical Engineering, Massachusetts Institute of Technology
David Hoffman
Affiliation:
Standard Microsystems Corporation, 35 Marcus Boulevard, Hauppauge, NY 11788
Di Ma
Affiliation:
Standard Microsystems Corporation, 35 Marcus Boulevard, Hauppauge, NY 11788
Get access

Abstract

A method for producing shallow silicided diodes for MOS devices (with junction depths of about 0.1 µm), by implanting after forming the silicide layer was investigated. The key to this integrated process is the use of rapid thermal annealing (RTA) to activate the dopants in the silicon, so that there is very little thermal broadening of the implant distribution. Self-aligned titanium silicide (TiSi2) films with thicknesses ranging from 40 to 80 nm were grown by RTA of sputter deposited titanium films on silicon substrates. After forming the TiSi2, arsenic and boron were implanted. A second RTA step was used after implantation to activate these dopants. It was found that implanting either dopant caused a sharp increase in the sheet resistivity of the TiSi2. The resistivity can be easily restored to its original value (about 18 µΩ-cm) by a post implant RTA anneal. RBS analysis showed that arsenic diffuses rapidly in the TiSi2 during RTA at temperatures as low as 600°C. SIMS data indicated that boron was not mobile up to temperatures of 900°C, possibly because it forms a compound with the titanium which precipitates in the TiSi 2. Coalescence of TiSi2 occurs during post implant furnace annealing, leading to an increase in the sheet resistivity. The amount of coalescence depends on the film thickness, but not on whether or not the film had been subject to implantation. Spreading resistance profiling data showed that both arsenic and boron diffused into the TiSi2 during furnace annealing, reducing the surface concentrations of dopant at the TiSi2/Si interface. Both N+/P and P+/N diodes formed by this technique exhibited low leakage currents after the second RTA anneal. This is attributed to removal of the implant damage by the RTA. In summary, the second RTA serves the dual purpose of removing implant damage in the TiSi2 and creating the shallow junction by dopant activation.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 146: Symposium B – Rapid Thermal Annealing/Chemical Vapor Deposition and Integrated Processing , 1989 , 191
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Murarka, S. P., J. Vac. Sci. Tech. 17 775 1980.CrossRefGoogle Scholar
[2] Murarka, S. P., Read, M. H., Doherty, C. J., and Fraser, D. B., J. Electrochem. Soc. 129 293 1982.Google Scholar
[3] Lau, C. K., See, Y. C., Scott, D. B., Bridges, J. M., Perna, S. M., and Davies, R. D., Proc. IEDM 714 (1982).Google Scholar
[4] Lanerolle, N. de, Hoffman, D., and Ma, D., J. Vac. Sci. Techaol. B 5 1689 1987.Google Scholar
[5] Biersak, J. P. and Eckstein, W., Appl. Phys. A. 34 73 1984.Google Scholar
[6] Gas, P., Deline, V., d, F. M.'Heurle, and Scilla, G., J. Appl. Phys. 60 1634 1986.Google Scholar
[7] Ommen, A. H. van, Houtum, H. J. W. van, and Theunissen, A. M. L., J. Appl. Phys. 60 627 1986.Google Scholar
[8] Probst, V., Schaber, H., Lippens, P., hove, L. Van den, and Keersmaecker, R. de, Appl. Phys. Lett 52 1803 1988.CrossRefGoogle Scholar
[9] Ku, Y. H., Louis, E., Lee, S. K., Shih, D. K., Kwong, D. L., Lee, C. O., and Yeargain, J. R., Advanced Processing of Semiconductor Devices, SPIE 797 61 1987.Google Scholar
[10] Yoshida, T., Fukumoto, M., and Ohzone, T., J. Electrochem. Soc., 135 481 1988.Google Scholar
[11] Amano, J., Merchant, P., and Koch, T., Appl. Phys. Lett., 44 744 1984.Google Scholar
[12] Shukla, R. K. and Multani, J. S., IEEE V-MIC Conf. 470 (1987).Google Scholar
[13] Ting, C. Y., d'Heurle, F. M., Iyer, S. S., and Fryer, P. M., J. Electrochem. Soc. 133 2621 1986.Google Scholar