Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-29T09:11:29.108Z Has data issue: false hasContentIssue false
  • English
  • Français

Flexible Substrate Based Gas Sensors for Air Pollution Monitoring

Published online by Cambridge University Press:  17 March 2011

S. Dmitriev ,
Gh. Duca ,
I. Dementiev  and
A. Craciun
S. Dmitriev
Affiliation:
Department of Industrial and Environmental Chemistry, Moldova State University
Gh. Duca
Affiliation:
Department of Industrial and Environmental Chemistry, Moldova State University
I. Dementiev
Affiliation:
Department of Physics, Moldova State University 60, A. Mateevici Str., Chisinau, MD-2009, Republic of Moldova
A. Craciun
Affiliation:
Department of Industrial and Environmental Chemistry, Moldova State University
Get access

Abstract

In the given report we present results of investigation of possibility to produce gas sensors on flexible substrates (polymer roll base). As gas sensitive materials were chosen glass chalcogenide semiconductors on the base of solid solutions of (As2S3)x-(As2Se3)1−x (where x=0; 0.3; 0.5; 0.7 and 1.0) and also solid solutions of As-Tl-S-Se system. Thin films of the mentioned above materials were deposited on lavsan roll film by means of thermal evaporation under vacuum conditions 10-5 Torr. At the thickness of 1-2 um the deposited layers are possessed the specific resistance in the range of 1010-1014 Ohm.cm on dependence on chemical composition.

The change of conductivity of these films in the presence of gas impurity in atmosphere was used as sensitive parameter. Gas sensitive characteristics of obtained structures were tested with such toxic and inflammable environmental pollutant gases as carbon monoxide, methane, nitrogen dioxide, hydrogen and other. All measurements of gas sensitivity were performed at room temperature. For further increase of the gas sensitivity and selectivity the very thin layer of Pd was deposited onto the surface of semiconductor layer. The last one has allowed to increasing the gas sensitive characteristics by order.

Through routine technology mode ready gas sensors were created. Dimensions of the developed gas sensitive elements were 1000×1000×350 μm.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 814: Symposium I – Flexible Electronics 2004-Materials and Device Technology , 2004 , I7.14
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Madou, M.J., Morrison, S.R., Chemical sensing with solid state devices. Academic Press, New York, 1989, p.75 Google Scholar
2. Lantto, V., in GasSensors, edited by Sberveglieri, G. (Kluwer Academic Publishers), Dordrecht, 1993 Google Scholar
3. Vincenzi, D., Butturi, M.A., Carotta, M.C. et al. , Sensors and Actuators B77, 91 (2001)Google Scholar
4. Lundstrom, I., Ederth, T., Kariis, H. et al. , Sensors and Actuators B23, 127 (1995)Google Scholar
5. Williams, D.E., Semiconducting oxides as gas sensitive resistors B57 1 (1999)Google Scholar
6. Gopel, W., Schierbaum, K.D., Sensors and Actuators B26–27, 1–12 (1995)Google Scholar
7. Marian, S., Tsiulyanu, D., Marian, T. et al. , Pure Appl.Chem. 73, p.2001 (2001)Google Scholar
8. Tsiuleanu, D., Marian, S., Miron, V., Patent MD 1725 (31 August 2001)Google Scholar
9. Senokosov, E.A., Ishimov, V.M. and Dementiev, I.V., PMR Patent No. 01 100229 (7 February 2001)Google Scholar
10. Moseley, P.T., Sensors and Actuators B 149 (1992)Google Scholar