Hostname: page-component-cd9895bd7-lnqnp Total loading time: 0 Render date: 2024-12-27T02:02:17.593Z Has data issue: false hasContentIssue false
  • English
  • Français

Fatigue Crack Growth in Co and Ni Base Directionally Solidified Eutectic Composites

Published online by Cambridge University Press:  15 February 2011

C. Hoffmann ,
P. Bhowal  and
A. J. Mcevily
C. Hoffmann
Affiliation:
Metallurgy Department, University of Connecticut, Storrs, CT 06268
P. Bhowal
Affiliation:
Formerly Post-doctoral Research Associate, University of Connecticut, now with Rockwell International, Troy, Michigan.
A. J. Mcevily
Affiliation:
Metallurgy Department, University of Connecticut, Storrs, CT 06268
Get access

Abstract

A study of fatigue crack growth behavior in four directionally solidified eutectic composites has been carried out in air at room temperature and at 870°C (1600 °F). The alloys investigated included two cobalt-base alloys, CoTaC and CoTaC+Cr, and two nickel base alloys, γ′-Mo and γ/γ′-δ. Fatigue crack growth was studied in directions parallel and perpendicular to the solidification direction. It was found that the addition of chromium to the CoTaC alloy strengthened the interface and promoted trans-fiber crack growth. In addition, the effect of interlamellar spacing on the rate of fatigue crack growth was examined for the γ/γ′-δ alloy. A reduction in interlamellar spacing reduced the crack growth rate. The growth rates are related to the corresponding stress intensity factors and are discussed in the light of prior investigations reported in the literature.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 12: Symposium L – In Situ Composites IV , 1981 , 69
Copyright
Copyright © Materials Research Society 1982

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Lawley, A., Conference on In-Situ Composites - II, Xerox, Lexington, MA, 1976, pp. 451–473.Google Scholar
2. Henry, M.F., Proc. Conf. on In-Situ Composites, pp. 173–186, NMAB-308-II, National Academy of Sciences – National Academy of Engineering, Washington, DC, 1973.Google Scholar
3. Woodford, D.A., Met. Trans., 1977, Vol. 8A, pp. 639–650.Google Scholar
4. Leverant, G.R. and Gell, M., Trans. TMS-AIME, 1969, Vol. 245, p. 1167.Google Scholar
5. Henry, M.F. and Stoloff, N.S., Fatigue of Composite Materials, ASTM STP 569, pp. 189–209.Google Scholar
6. Yuen, A. and Leverant, G.R., Met. Trans., September 1976, Vol. 7A, pp. 1443–1450.Google Scholar
7. Scarlin, B., Met. Trans., December 1977, Vol. 8A, pp. 1941–1948.Google Scholar
8. Austin, C.M., Stoloff, N.S. and Duquette, D.J., Met. Trans., October, 1977, Vol. 8A, pp. 1621–1627.Google Scholar
9. Mills, W.J. and Hertzberg, R.W., Fatigue of Composite Materials, ASTM STP 569, 1975, pp. 5–27.Google Scholar
10. Sadananda, K. and Shahinian, P., Materials Science and Engineering, Vol. 38, 1979, pp. 81–88.Google Scholar
11. Bretz, P. E. and Hertzberg, R.W., Journal of Materials Science, Vol. 14, 1979, pp. 265–274.Google Scholar
12. Scarlin, R.B., Metallurgical Transactions, Vol. 7A, October 1976, pp. 1535–1541.Google Scholar
13. Annual Book of ASTM Standards, Vol. 10, E 399–74, ASTM, Philadelphia, PA, 1974, pp. 432–451.Google Scholar
14. Gouda, M., Prewo, K.M. and McEvily, A.J., Fatigue of Fibrous Composite Materials, ASTM STP 723, 1981, pp. 101–115.Google Scholar