Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-27T05:35:24.869Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication of Microfluidic Devices in Thermoplastic Elastomeric Materials for DNA Detection on Thermal Plastic Substrate

Published online by Cambridge University Press:  31 January 2011

Kebin Li ,
Daniel Brassard ,
François Normandin ,
Caroline Miville-Godin ,
Matthias Geissler ,
Emmanuel Roy  and
Teodor Veres
Kebin Li
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Daniel Brassard
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
François Normandin
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Caroline Miville-Godin
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Matthias Geissler
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Emmanuel Roy
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Teodor Veres
Affiliation:
[email protected], National Research Council Canada, Industrial Materials Institute, Boucherville, Canada
Get access

Abstract

Thermoplastic elastomer (TPE) based microfluidic devices integrated with a microfluidic pumping manifold which consists of 4 electromagnetic valves (EMV) were fabricated. The back and forth shuttling flow and its application in the DNA hybridization process were validated on a thermal plastic Zeonor 1060R substrate. The flow rate can be as fast as 23μl/min when the channel width and the channel height are in 100μm, and 25μm, respectively. The DNA hybridization process is detected by using a fluorescence microscopy. Remarkable DNA hybridization is achieved with the continuous flow of the target DNA at a concentration of 10 nM within the first 1 min by using this device.

Keywords

fluidicshot pressingmicroelectro-mechanical (MEMS)
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1222: Symposium DD – Microelectromechanical Systems — Materials and Devices III , 2009 , 1222-DD05-24
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1]. Xia, Y.N. et al. , Ann. Rev. Mater. Sci. 1998, 28:1800 Google Scholar
[2]. Marshall, A. et al. Nat. Biotechnology. 1998, 16, 27–31.Google Scholar
[3]. Dufva, M. Biomol. Eng., 2005, 22, 173–184.Google Scholar
[4]. Roy, E., Geissler, M. Galas, J. C. Diaz-Quijada, G. A. and Veres, T., Submitted to Lab on Chip 2009Google Scholar
[5]. Geissler, M. Roy, E. Diaz-Quijada, G.A., Galas, J. C. and Veres, T. ACS Applied Materials & Interfaces 2009, 1(7), 1387.Google Scholar
[6]. Guillemette, Maxime D. et al. , Integr. Biol., 2009, 1, 196–204.Google Scholar
[7]. Brassard, D. Li, K. Roy, E. and Veres, T. to be submitted.Google Scholar
[8]. Kim, Joshua Hyong-Seok, Marafie, Alia, Xi-Yu Jia, Jim Zoval Marc, V. Madou, J. Sensors and Actuators B 2006, 113, 281–289.Google Scholar