Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-29T08:03:46.698Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhancement of Adhesion Between Cu Thin Film and Polyimide Modified by Ion Assisted Reaction

Published online by Cambridge University Press:  10 February 2011

S. C. Choi ,
K. H. Kim ,
H-J. Jung ,
C. N. Whang  and
S. K. Koha
S. C. Choi
Affiliation:
Thin Film Technology Research Center, Korea Institute of Science and Technology, P.O.Box 131 Cheongryang, Seoul, 130–650, Korea
K. H. Kim
Affiliation:
Thin Film Technology Research Center, Korea Institute of Science and Technology, P.O.Box 131 Cheongryang, Seoul, 130–650, Korea
H-J. Jung
Affiliation:
Thin Film Technology Research Center, Korea Institute of Science and Technology, P.O.Box 131 Cheongryang, Seoul, 130–650, Korea
C. N. Whang
Affiliation:
Department of Physics, Yonsei University, Shinchondong, Seodemoongu, Seoul, 120–749, Korea
S. K. Koha
Affiliation:
Thin Film Technology Research Center, Korea Institute of Science and Technology, P.O.Box 131 Cheongryang, Seoul, 130–650, Korea
Get access

Abstract

Polyimide films are modified by ion assisted reaction method using various ion beams in various gases environments. Amount of ion and blown gases rate were changed from 5 × 1014 to 1 × 1017 and from 0 to 8 sccm, respectively. Wetting angles between water and polyimide films modified by Ar+ ion without oxygen blowing decrease from 67° to 400° and surface free energies increase from 46 to 64 dyne/cm2. Wetting angle of polyimide films modified by Ar+ ion in an oxygen environment decreases to 12° and surface free energy increases to 72 dyne/cm2. The lowest wetting angle was obtained by oxygen ion irradiation in the oxygen gas environment and its value was 7°. In the case of polyimide film modified by Ar+ ions in an oxygen environment, the wetting angle increases up to 65° when it kept in air and that increases up to 46° when it kept in water after 5 day. In the case of polyimide film modified by O2+ ion in oxygen environment, however, the wetting angle of polyimide film dose not increase. X-ray photoelectron analysis shows that the chemical bonds between polyimide components are severed by ion irradiation and hydrophilic groups such as CO and C=O are formed by the reaction between newly formed radicals and blown oxygen. It was found that adhesion between Cu and polyimide modified by ion assisted reaction was improved. The main reason of the enhanced adhesion is due to the reaction between Cu and C-O or C=O groups formed by ion assisted reaction on the polyimide surface.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 504: Symposium KK – Atomistic Mechanisms in Beam Synthesis & Irradiation… , 1997 , 437
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Wilson, A. M., Polyimides-Synthesis. Characterization and Applications. Mittal, K. L., ed. ( Plenum, New York, 1984) p. 715.Google Scholar
2. Jensen, R. J., Cummings, J. P., and Vora, H., IEEE Trans. Components Hybrids Manuf. Technol. 7, 385 (1984).Google Scholar
3. Koh, S. K., Pae, K. D., and Caracciolo, R., Polym. Eng. Sci. 32, 558 (1992).Google Scholar
4. Chenite, A., Selmani, A., and Yelon, A., J. Vac. Sci. Technol. A12, 513 (1994).Google Scholar
5. Lj. Atanasoska, Anderson, S. G., Meyer, H. M. III, Lin, Z. and Weaver, J. H.. J. Vac. Sci. Technol. A5, 3325 (1987).Google Scholar
6. Forest, S. R.. Kaplan, M. L., Schmidt, P. H., Venkatesan, T. and Lovinger, A. E., Appl. Phys. Lett. 41, 708 (1982).Google Scholar
7. Hultman, L., Helmersson, U., Barnett, S. A., Sundgren, J. E. and Greene, J. E., J. Appl. Phys. 61, 552 (1987).Google Scholar
8. Koh, S. K., Park, S. C., Kim, S. R., Choi, W. K., Jung, H-J., and Pae, K. D., J. Appl. Polym. Sci. 64, 1913 (1997).Google Scholar
9. Cho, J. S., Choi, W. K., Jung, H-J. and Koh, S. K., J. Mater. Res. 312, 277 (1996).Google Scholar
10. Koh, S. K., Choi, W. K., Cho, J. S., and Jung, H-J., J. Mater. Res. 11, 2933 (1996).Google Scholar
11. Choi, W. K., Koh, S. K. and Jung, H-J., J. Vac. Sci. Technol. A14, 2366, (1996).Google Scholar
12. Ma, J. B., Dragon, J., Derveer, W. V., Entenberg, A., Lindberg, V., Anschel, M., Shih, D. Y., and Lauro, P., Adhesion, J.. Sci. Technol. 9, 487 (1995).Google Scholar
13. Ramb, R. N., Baxter, J., Grunze, M., Kong, C. W., and Unertl, W. N., Langmuir 4, 249 (1988).Google Scholar
14. Marletta, G., Oliveri, C., Ferla, G., and Pignataro, S., Surf and Inter. Anal. 12, 447 (1988).Google Scholar
15. Flisch, R. and Shin, D-Y., J. Vac. Sci. Technol. A8, 2376 (1990).Google Scholar
16. Height, R., White, R. C., Silverman, B. D., and Ho, P. S., J. Vac. Sci. Technol. A6, 2188(1991).Google Scholar
17. King, D. E., Czandema, A. W., and Spaulding, D., Metallized plastics 3 edited by Mittal, K. L. and Susko, J. R. (Plenum press, NewYork, 1989) pp. 149–161 Google Scholar
18. Droulas, J. L., Jugnet, Y., and Due, T. M., ibid., pp. 123–140.Google Scholar