Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-11-25T15:53:40.907Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of Pd/Mn Substitution on Characteristics of Amorphous Zr-Ni-Ti-V Alloy Hydride Electrodes

Published online by Cambridge University Press:  09 January 2012

Hiroshi Miyamura ,
Yoshihisa Fujita  and
Balachandran Jeyadevan
Hiroshi Miyamura
Affiliation:
The University of Shiga Prefecture, 2500 Hassaka-cho, Hikone 522-8533, JAPAN
Yoshihisa Fujita
Affiliation:
The University of Shiga Prefecture, 2500 Hassaka-cho, Hikone 522-8533, JAPAN
Balachandran Jeyadevan
Affiliation:
The University of Shiga Prefecture, 2500 Hassaka-cho, Hikone 522-8533, JAPAN
Get access

Abstract

Hydrogenation properties of some amorphous Zr-Ni-Ti-V based alloys were investigated. Pressure-composition(P-C) isotherms and hydrogen storage capacities at room temperatures were measured and effects of elemental substitution of the components with Pd or Mn were studied. The alloy electrodes were prepared by using amorphous (Zr-Ni-Ti-V)-(Pd,Mn) alloys prepared by the melt spinning method. The amorphous alloys in the electrode kept their amorphous structures during cycles of charge and discharge. The electrochemical hydrogen storage capacities were strongly affected by the substitution amounts of Pd or Mn. Even a small amount of substitution, changed the equilibrium dissociation pressures of the alloy. In the present study, the rechargeable capacity was optimized up to H/M=0.5 for the alloy electrode with the composition of (Zr45Ni30Ti25)-3at%Pd. The slope in the P-C isotherm suggested that the maximum H/M of the alloy would exceed 1.0 at higher hydrogen pressure than 1.0 MPa, however, the wide distribution of hydrogen site energy in the amorphous hydride resulted in extremely large slope in P-C isotherms, and consequently restricted the rechargeable capacities of the electrodes.

Keywords

amorphousenergy storagehydrogenation
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1388: Symposium F – Mobile Energy , 2012 , mrsf11-1388-f04-22
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Justi, J E.W., Ewe, H.H., Kalberlar, A.W., Saridakis, N.M. and Schaefer, M.H., Energy Conver., 10,(1970)183.Google Scholar
2. Ewe, H.H., Justi, E.W., and Stephan, K., Energy Conver., 13,(1973)109. Willems,Google Scholar
3. Willems, J.J.G., Phillips J. Res., 39(1984)1–.Google Scholar
4. Kohno, T., J. Alloys and Compnds 363(2004) 254–257 Google Scholar
5. Chai, Y.J., Sakaki, K., Asano, K., Enoki, H., Akiba, E., Kohno, T., Scripta Mater. 57(2007)545–548 Google Scholar
6. Suzuki, K., J. Less-Common Met., 89(1983)183.Google Scholar
7. Libowits, G. G. and Maeland, A. J., J. Less-Common Met 101(1984)131.Google Scholar
8. Aoki, K., Kamachi, M., and Masumoto, T., J. Non-cryst. Solids 61/62(1984)679 Google Scholar
9. Aoki, K., Masumoto, T., and Kamachi, M., J. Less-Common Met., 113(1985)33.Google Scholar
10. Kirchheim, R., Sommer, F. and Schluckebier, G., Acta Met., 30(1982)1059–1067.Google Scholar
11. Varga, L.K.: J. Alloys and Compnds, 231,(1995) 321–324)Google Scholar