Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-25T17:55:56.533Z Has data issue: false hasContentIssue false
  • English
  • Français

Diffusion Bonding Of Ti-48A1-2Mn-2Nb (at. %)

Published online by Cambridge University Press:  22 February 2011

S. P. Godfrey ,
P. L. Threadgill  and
M. Strangwood
S. P. Godfrey
Affiliation:
Department of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham, B15 2TT, U.K. Phone 021 414 5220. Fax 021 414 5232.
P. L. Threadgill
Affiliation:
TWI, Abington Hall, Abington, Cambridge, CB1 6AL, U.K. Phone 0223 891162.Fax 0223 892588
M. Strangwood
Affiliation:
Department of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham, B15 2TT, U.K. Phone 021 414 5220. Fax 021 414 5232.
Get access

Abstract

The diffusion bonding behaviour of Ti-48at.%Al-2at.%Mn-2at.%Nb has been studied as a function of temperature (in the range 1200–1350°C), time (15–45 minutes) and starting microstructure (lamellar, duplex and near γ) at constant bonding pressure of 10 MPa. It was found, that under the above conditions, small twin related γ grains, approximately 10–20 μm in size, nucleated at the original interface and grew into the matrix forming a double necklace grain structure. Particles of α2 were observed around the interface, the formation of α2 particles was believed to be related to oxygen partitioning and stabilisation effects from dissolved oxide films during the bonding process. Evidence for this mechanism was obtained from parallel electron energy loss spectroscopy (PEELS), which identified oxygen partitioning in the α2 particles. For the fully lamellar structure bonded at 1250°C for 45 minutes the failure strength of the bond was found to be 250 MPa, approximately 50 MPa lower than the failure strength of the base material.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 364: Symposium L – High-Temperature Ordered Intermetallic Alloys–VI , 1994 , 793
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Nakao, Y., Shinozaki, K., Hamanda, M.. ISIJ International, Vol. 31 (1991), No 10, pp 1260–1266.Google Scholar
2. Hill, A. and Wallach, E.R., Acta Metall., Vol. 37, No 9 (1989), pp 2425–2437.Google Scholar
3. Ridley, N., Guo, Z.X.. Materials Science and Technology, Vol. 3 (November 1987), pp 945–953.Google Scholar
4. Vasudevan, V.K., Court, S.A., Kurath, P., Fraser, H.L.. Scripta Metallurgica, Vol. 23 (1989), pp 907–912.Google Scholar
5. Denquin, A., Naka, S., Huguet, A., Menand, A. Scripta Metallurgica et Materialia, Vol. 28 (1993), pp 1131–1136.Google Scholar
6. Yamaguchi, M., Inui, H., Nakamura, A.. Mat. Res. Soc. Proc, Vol. 213 (1991), pp 569–574.Google Scholar
7. Bowen, P., James, A.W., Chave, R.A., Hippsley, C.A.. 3rd European Conference on Advanced Materials and Processing. Journal de Physique III, Vol.3, November 1993, pp 411–421.Google Scholar
8. Kim, Y-W., Dimiduk, D.M.. Journal of The Minerals, Metals and Materials Society, Vol.43, No.8 (August 1991), pp 40–56.Google Scholar
9. Kennedy, I.R.B.. Unpublished research.Google Scholar