Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-09T09:08:12.028Z Has data issue: false hasContentIssue false
  • English
  • Français

A Comparison and Abstraction of the Commercial Spent Fuel Corrosion Experiments in the U.S.

Published online by Cambridge University Press:  11 February 2011

Eric R. Siegmann
Eric R. Siegmann*
Affiliation:
Framatome ANP, 1180 Town Center Drive, Las Vegas, NV 89144, U.S.
Get access

Abstract

This paper compares the results of three different fuel corrosion experiments by taking the existing corrosion data reported for various temperatures and recalculating corrosion rates at a single temperature of 25°C using a temperature dependent model developed elsewhere. Three types of light water reactor fuel corrosion tests (sometimes called dissolution or alteration tests) were performed in support of Yucca Mountain Project. The tests used three water contact modes and various fuel burnups. All measurements were adjusted for temperature differences and then compared. Five different isotopes (cesium, technetium, iodine, strontium, and, in the flow-through tests, uranium) were considered as a measure of corrosion. The data used represent over ten years of experiments with about nine different fuel types. Most experiments were with repository type fluids, containing dissolved constituents such as carbonate, calcium and silicon. The results show that all of the experiments predict similar fuel corrosion rates. Small differences in the isotope release rates are observed and incorporated in the abstracted uncertainty. Water contact mode (flow-through, batch, or drip) does not seem to be very important although the drip tests introduced larger variations. In developing a corrosion abstraction, all of the isotope measurements were considered equally. The distribution of release rates was used directly to develop the uncertainty. The mean corrosion rate was 1.8 × 10-4 fraction/year at 25°C (5%-95% range = 5.7 × 10-5 to 1.7 × 10-3). Using the derived corrosion rate for 25°C, and considering rapid axial splitting of the cladding, the CSNF fuel rod is expected to corrode in less than 2,000 years. The abstraction uses all the available experiments performed with water containing carbonates, silicon, or calcium and irradiated fuel to produce a corrosion rate distribution. Sensitivity studies using this corrosion rate abstraction in the TSPA-SR analysis show very small changes in dose (3%) in response to changes in the UO2 corrosion abstraction.

Type
articles
Information
MRS Online Proceedings Library (OPL) , Volume 757: Symposium II – Scientific Basis for Nuclear Waste Management XXVI , 2002 , II9.6
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Stewart, S., ANL-EBS-MD-000015 REV 00, CRWMS M&O, Las Vegas, Nevada, 2000.Google Scholar
2. Gray, W.J. and Wilson, C.N., PNL-10540. Pacific Northwest Laboratory, Richland, Washington, 1995.Google Scholar
3. Wilson, C.N., HEDL-TME-84–30, Hanford Engineering Development Laboratory, Richland, Washington, 1985 Google Scholar
4. Wilson, C.N., PNL-7169, Pacific Northwest Laboratory, Richland, Washington, 1990.Google Scholar
5. Wilson, C.N., PNL-7170, Pacific Northwest Laboratory, Richland, Washington, 1990.Google Scholar
6. Finch, R.J., Buck, E.C., Finn, P.A., Bates, J.K., in Scientific Basis for Nuclear Waste Management XXII, edited by Wronkiewicz, D.J. and Lee, J.H. (Mater. Res. Soc. Proc. 556, Pittsburgh, PA, 1999) pp.431–438.Google Scholar
7. Cunnane, J.C., Letter to C. Stockman, August 16, 2001, Progress in Waste Form Task, June and July, 2001 (unpublished).Google Scholar
8. Forsyth, R.S. and Werme, L.O., SKB TR 91–60, Studsvik AB, Nykoping, Sweden, 1992.Google Scholar