Hostname: page-component-cd9895bd7-gbm5v Total loading time: 0 Render date: 2024-12-24T00:57:05.106Z Has data issue: false hasContentIssue false
  • English
  • Français

Chemical Gas Generators Based on Mechanically Alloyed Al·Mg Powder

Published online by Cambridge University Press:  17 March 2015

Marco A. Machado ,
Daniel A. Rodriguez ,
Edward L. Dreizin  and
Evgeny Shafirovich
Marco A. Machado
Affiliation:
Department of Mechanical Engineering, The University of Texas at El Paso, El Paso, TX 79968, U.S.A.
Daniel A. Rodriguez
Affiliation:
Department of Mechanical Engineering, The University of Texas at El Paso, El Paso, TX 79968, U.S.A.
Edward L. Dreizin
Affiliation:
Department of Chemical, Biological, and Pharmaceutical Engineering, New Jersey Institute of Technology, Newark, NJ 07102, U.S.A.
Evgeny Shafirovich
Affiliation:
Department of Mechanical Engineering, The University of Texas at El Paso, El Paso, TX 79968, U.S.A.
Get access

Abstract

Because of the high energy density, easy ignition, and good storability, mechanically alloyed Al·Mg powder has the potential to improve the performance characteristics of various energetic and gas-generating materials. Here, the use of this powder in combustible mixtures for generation of oxygen and hydrogen is explored. The mixtures for oxygen generation consisted of sodium chlorate, nanoscale cobalt oxide catalyst, and Al·Mg powder, while those for hydrogen generation included water, polyacrylamide as a gellant, and Al·Mg powder. To increase hydrogen yield, ammonia borane (NH3BH3) was also added to Al·Mg − water mixtures. Combustion experiments were conducted in an argon environment, using laser ignition. The thermal wave propagation over the oxygen-generating mixtures was studied using infrared video recording. It has been shown that mechanically alloyed Al·Mg material is a promising alternative to currently used iron because significantly smaller amounts of this additive are needed for a steady propagation of the combustion wave. The hydrogen generation experiments have shown that mixtures of mechanically alloyed Al·Mg powder with 10−60 wt% gelled water are combustible, with the front velocities exceeding the values obtained for the mixtures of water with nanoscale Al. Hydrogen yield was measured using mass-spectrometry. In the mixtures that included ammonia borane, D2O was used instead of H2O. Measurements of H2, D2, and HD concentrations in the product gas provided insight into the reaction mechanisms. The isotopic tests have shown that AB participates in two parallel processes − thermolysis and hydrolysis, thus increasing hydrogen yield.

Keywords

energetic materialmechanical alloyingmass spectroscopy
Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 1758: Symposium VV – Recent Advances in Reactive Materials , 2015 , mrsf14-1758-vv04-03
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Shoshin, Y.L., Mudryy, R.S., and Dreizin, E.L., Combust. Flame 128, 259–269 (2002).CrossRefGoogle Scholar
Shoshin, Y.L. and Dreizin, E.L., Combust. Flame 145, 714–722 (2006).CrossRefGoogle Scholar
Aly, Y., Schoenitz, M., and Dreizin, E.L., Combust. Flame 160, 835–842 (2013).CrossRefGoogle Scholar
Aly, Y., Hoffman, V.K., Schoenitz, M., and Dreizin, E.L., J. Propul. Power 30, 96–104(2014).CrossRefGoogle Scholar
Mausteller, J.W., in Kirk-Othmer Encyclopedia of Chemical Technology, 4th ed., edited by Kroschwitz, J. I. and Howe-Grant, M. (Wiley, New York, 1996), Vol. 17, p.940−952.Google Scholar
Wydeven, T., J. Catal. 19, 162–171 (1970).CrossRefGoogle Scholar
Zhang, Y., Kshirsagar, G., Ellison, J.E., and Cannon, J.C., Thermochim. Acta 228, 147–154 (1993).CrossRefGoogle Scholar
Shafirovich, E., Garcia, A., Narayana Swamy, A.K., Mast, D.J., and Hornung, S.D., Combust. Flame 159, 420−426 (2012).CrossRefGoogle Scholar
Shafirovich, E., Mukasyan, A.S., Varma, A., Kshirsagar, G., Zhang, Y., and Cannon, J.C., Combust. Flame 128, 133–144(2002).CrossRefGoogle Scholar
Shafirovich, E., Zhou, C., Mukasyan, A.S., Varma, A., Kshirsagar, G., Zhang, Y., and Cannon, J.C., Combust. Flame 135, 557–561(2003).CrossRefGoogle Scholar
Diakov, V., Shafirovich, E., and Varma, A., AIChE J. 52, 1495–1501(2006).CrossRefGoogle Scholar
Stephens, F.H., Pons, V., and Baker, R.T., Dalton Trans. 2007, 2613−2626.CrossRefGoogle Scholar
Staubitz, A., Robertson, A.P.M., and Manners, I., Chem. Rev. 110, 4079−4124(2010).CrossRefGoogle Scholar
Diwan, M., Diakov, V., Shafirovich, E., and Varma, A., Int. J. Hydrogen Energy 33, 1135−1141 (2008).CrossRefGoogle Scholar
Aly, Y., Schoenitz, M., and Dreizin, E.L., Combust. Flame 160, 835−842 (2013).CrossRefGoogle Scholar
Aly, Y., Hoffman, V.K., Schoenitz, M., and Dreizin, E.L., J. Propul. Power 30, 96−104 (2014).CrossRefGoogle Scholar
Kravchenko, O.V., Sevastyanova, L.G., Urvanov, S.A., and Bulychev, B.M., Int. J. Hydrogen Energy 39, 5522−5527 (2014).CrossRefGoogle Scholar
Shkadinskii, K.G., Khaikin, B.I., and Merzhanov, A.G., Combust. Explos. Shock Waves 7, 15−22 (1971).CrossRefGoogle Scholar
Bouaricha, S., Dodelet, J.P., Guay, D., Huot, J., Boily, S., and Schulz, R., J. Alloy Compd. 297, 282–293 (2000).CrossRefGoogle Scholar
Habu, H., Keikinzoku /J. Japan Inst. Light Metals 58, 162–166 (2008).CrossRefGoogle Scholar
Ivanov, V.G., Gavrilyuk, O.V., Glazkov, O.V., and Safronov, M.N., Combust. Explos. Shock Waves 36, 213−219 (2000).CrossRefGoogle Scholar
Risha, G.A., Sabourin, J.L., Yang, V., Yetter, R.A., Son, S.F., and Tappan, B.C., Combust. Sci. Technol. 180, 2127−2142 (2008).CrossRefGoogle Scholar
Shiryaev, A.A., Int. J. SHS 4, 351−362 (1995).Google Scholar