Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-06T01:10:19.397Z Has data issue: false hasContentIssue false

BaZrO3Thin Films For Humidity Gas Sensor

Published online by Cambridge University Press:  01 February 2011

XiaoXin Chen
Affiliation:
[email protected], University of Utah, Electrical and Computer Engineering, 50 S. Central Campus Drive, SLC, UT, 84112, United States
Michael Sorenson
Affiliation:
Mike Sorenson ,, University of Utah, Electrical and Computer Engineering, Salt Lake City, UT, 84102, United States
Clayton Butler
Affiliation:
[email protected], University of Utah, Electrical and Computer Engineering, SLC, UT, 84102, United States
Loren Rieth
Affiliation:
[email protected], University of Utah, Electrical and Computer Engineering, Salt Lake City, UT, 84102, United States
Mark S. Miller
Affiliation:
, Univeristy of Utah, Electrical and Computer Engineering and Material Science, SLC, UT, 84102, United States
Florian Solzbacher
Affiliation:
[email protected], University of Utah, Electrical and Computer Engineering, Material Science, and Bioengineering Department, SLC, UT, 84102, United States
Get access

Abstract

Microscale (MEMS) gas sensing devices for power plant and automobile exhaust gas are being developed. Bulk BaZrO3 has been previously found to be sensitive to H2O at high temperatures, but was never studied in a thin film form. This research thrust focuses on undoped BaZrO3 and doped BaZrO3 with Y.

Thin films were deposited on oxidized n-type silicon substrates at room temperature from ceramic targets with an Ar sputtering ambient. Various deposition pressures and deposition powers were used for the initial investigation. The structural and electrical properties of the deposited films were characterized to investigate their relationships to the deposition process parameters. X-ray diffraction (XRD) was used to measure the crystal structure of the deposited films, and in particular was used to determine if any crystallographic texture is present in the films. XRD results indicate the as-deposited films are amorphous before annealing. Films sputtered with and without oxygen in the ambient were compared. The crystal structure and morphology of BaZrO3 and BaZrO3 doped with Y after annealing were also determined. The materials changed from amorphous to crystalline after annealing at temperatures of 800 °C and 1000 °C for 3 hours in forming gas (2% H2 balanced with Ar gas) and oxygen. Temperature was found to dominate over deposition conditions in determining the final film structure. Atomic force microscopy was used to examine the morphology of the thin films. Gas sensor test structures using a Pt thin film metallization for interdigitated electrode structures were fabricated for gas sensing measurements. The experiments with the completed test structures measured the materials¡¦ resistivity as a function of temperature and gas concentration. Both materials decrease in resistance with increasing temperature, which is consistent with ionic conduction. Some experiments tested the gas sensitivity and selectivity of the films to the target gas H2O vapor (humidity) and possible cross sensitive gases H2 and CO2. Both materials need further development to evaluate their suitability for thin film sensors. First, the films were found to be highly resistive, making characterization of the electrical properties very difficult. Second, O2 ambient annealing gas will be applied to compare the crystal structure and morphology of both films with an Ar ambient annealing process.

Type
Research Article
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Merinov, B., Dorso, C.O., Goddard, W.A. III , Wu, J., and Haile, S.. “Enhanced power stability for proton conducting solid oxides fuel cells”, Semi-Annual Progress Report, CIT, Oct. 2003.Google Scholar
2. Schnellr, T., and Schober, T., “Chemical solution deposition prepared dense proton conducting Y-doped BaZrO3 thin films for SOFC sensor devices”, Solid state Ions., June, 2003.Google Scholar
3. Ho, Justin, Heifets, Eugene, and Merinov, Boris, “Ab initio simulation of the BaZrO3 (001) surface structure”, Surface Sci, Oct, 2006.Google Scholar
4. Haile, S.M., Staneff, G., Ryu, K.H., J. Mat Sci. 36 (2001) 1149.Google Scholar
5. Yamazoe, N., Shimizu, Y., Sens. Actuators 10 (1986) 379398.Google Scholar
6. Kulwicki, B. M., J. Am. Ceramc. Soc., 74 (1991) 697708.Google Scholar
7. Traversa, E., Sens. Actuators B Chem. 23 (1995) 135136.Google Scholar
8. Terki, R., Feraoun, H., Bertrand, G., and Aourag, H., “Full potential calculation of structural, elastic and electronic properties of BaZrO3 and SrZrO3”, phys. stat. sol. (b) 242, No.5, 10541062 (2005).Google Scholar