Hostname: page-component-586b7cd67f-g8jcs Total loading time: 0 Render date: 2024-11-23T08:49:29.508Z Has data issue: false hasContentIssue false

Stress-Induced Void Formation in Metal Lines

Published online by Cambridge University Press:  29 November 2013

Get access

Extract

The problem of stress-induced voiding in the metal lines used for VLSI interconnections appeared about 10 years ago and was first reported in the literature in 1984. Some typical voids are shown in Figure 1. It is not entirely coincidental that the problem is of about the same age as the personal computer. The continuing advances in process technology that make possible the ever lower costs and improved performance of VLSI devices often have unexpected and troublesome side effects. Continuous attention to potential effects of process changes on the behavior of the materials comprising a VLSI chip is essential to avoid passing on problems to customers. The history of stress-induced voiding provides a good illustration.

Type
Materials Reliability in Microelectronics
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Klema, J., Pyle, R., and Domangue, E., in Proc. 22nd Annu. Int. Reliability Symp. (IEEE, New York, 1984) p. 1.Google Scholar
2.Curry, J., Fitzgibbon, G., Guan, Y., Muollo, R., Nelson, G., and Thomas, A., in Reference 1, p. 6.Google Scholar
3.Flinn, P.A., Gardner, D.S., and Nix, W.D., IEEE Trans. Electron Devices ED-34 (1987) p. 689.CrossRefGoogle Scholar
4.Landolt-Bornstein, New Series, edited by Hellwege, K., Vol. III, No. 11 (Springer-Verlag, New York, 1979).Google Scholar
5.Brantley, U.A., J. Appl. Phys. 44 (1973) p. 534.CrossRefGoogle Scholar
6. Umis-2000 ultra micro-indentation system, manufactured by CSIRO Division of Applied Physics, National Measurement Laboratory, Lindfield, NSW, Australia.Google Scholar
7.Sinha, A.K., Levenstein, H.J., and Smith, T.E., J. Appl. Phys. 49 (1978) p. 2423.CrossRefGoogle Scholar
8.Mclnerney, E.J. and Flinn, P.A., in Proc. 20th Annu. Int. Reliability Symp. (IEEE, New York, 1982) p. 264.Google Scholar
9.Flinn, P.A., in Thin Films: Stresses and Mechanical Properties, edited by Bravman, J.C., Nix, W.D., Barnett, D.M., and Smith, D. A. (Mater. Res. Soc. Symp. Proc. 130, Pittsburgh, PA, 1989) p. 41.Google Scholar
10.Flinn, P.A., J. Mater. Res. 6 (1991) p. 1498.CrossRefGoogle Scholar
11.Jones, R.E., in Proc. 25th Annu. Int. Reliability Symp. (IEEE, New York, 1987) p. 9.Google Scholar
12.Sauter, A.I. and Nix, W.D., in Thin Films: Stresses and Mechanical Properties II, edited by Doerner, M., Oliver, W.C., Pharr, G.M., and Brotzen, F.R. (Mater. Res. Soc. Symp. Proc. 188, Pittsburgh, PA, 1990) p. 15.Google Scholar
13.Sauter, A.I., PhD thesis, Stanford University, 1991.Google Scholar
14.Sauter, A.I. and W Nix, D., IEEE Trans. Components, Hybrids, and Manufacturing Technology 15 (1992) p. 594.CrossRefGoogle Scholar
15.Moske, M., Ho, P., Hu, C.K., and Small, M., in Stress-Induced Phenomena in Metallization, edited by Li, C., Totta, P., and Ho, P. (American Institute of Physics, New York, 1992) p. 195.Google Scholar
16.Flinn, P.A. and Waychunas, G.A., J. Vac. Sci. Technol. B 6 (1988) p. 1749.CrossRefGoogle Scholar
17.Flinn, P.A. and Chiang, C., J. Appl. Phys. 67 (1990) p. 2927.CrossRefGoogle Scholar
18.Besser, P., Mack, A.S., Fraser, D., and Bravman, J., in Materials Reliability in Microelectronics III, edited by Rodbell, K., Filter, B., Ho, P., and Frost, H. (Mater. Res. Soc. Symp. Proc. 309, Pittsburgh, PA, 1993) p. 287.Google Scholar
19.Hasunuma, M., Kaneko, H., Sawabe, A., Kawanoue, T., Kohanawa, Y., Komatsu, S., and Miyauchi, M., Proc. IEEE Electron Devices Meeting, IEDM 89 (IEEE, New York, 1989) p. 677.Google Scholar
20.Greenebaum, B., Sauter, A.I., Flinn, P.A., and Nix, W D., Appl. Phys. Lett. 58 (1991) p. 1845.CrossRefGoogle Scholar
21.Abe, H., Tanabe, S., Kondo, Y., and Ikubo, M., in Extended Abstracts (Jpn. Soc. Appl. Phys., 39th Spring Meeting, April 1992) p. 658.Google Scholar
22.Nix, W. and Sauter, A.I., Modelling Void Growth and failure of Passivated Metal Lines under Stress and Electromigration Conditions, (American Institute of Physics, New York, 1992) p. 89.Google Scholar
23.Nix, W.D. and Arzt, E., “On Void Nucleation and Growth in Metal Interconnect Lines Under Electromigration Conditions,” private communication.CrossRefGoogle Scholar
24.Peek, H.L. and Wolters, R.A.M., in Proc. 3rd Int. IEEE VLSI Multilevel Interconnection Conf. (IEEE, New York, 1986) p. 165.Google Scholar
25.Filter, W.F. and Ayle, J.A.V.D., “A Test Vehicle to Assess Stress Voiding Models and Acceleration Methods,” in Proc. First Int. Workshop on Stress-Induced Phenomena in Metallizations (American Physical Society, New York, 1992).Google Scholar
26.Albrecht, J., Bernstein, I.M., and Thompson, A.W., Metall. Trans. A 13A (1982) p. 811.CrossRefGoogle Scholar
27.Murali, V., Sachdev, S., Banerjee, I., Casey, S., and Gargini, P., in Proc. 7th Int. IEEE VLSI Multilevel Interconnection Conf. (IEEE, New York, 1990) p. 127.Google Scholar
28.van Houtum, H., Tibbe, J., and Dirks, A., in Proc. 8th Int. IEEE VLSI Multilevel Interconnection Conf. (IEEE, New York, 1991) p. 235.Google Scholar
29.Ryan, J.G., Riendeau, J.B., Shore, S.E., Slusser, G.J., Beyar, D.G., Bouldin, D.P., and Sullivan, T.D., J. Vac. Sci. Technol. A 8 (1990) p. 1474.CrossRefGoogle Scholar
30.Shin, H., in Reference 24, p. 292.CrossRefGoogle Scholar
31.Yamaji, T., Igarshi, Y., and Nishikawa, S., in Proc. 29th Annu. Int. Reliability Symp. (IEEE, New York, 1991) p. 84.Google Scholar
32.Madden, M.C., Abratowski, E.V., Marieb, T., and Flinn, P.A., in Materials Reliability in Microelectronics II, edited by Thompson, C.V. and Lloyd, J. R. (Mater. Res. Soc. Symp. Proc. 265, Pittsburgh, PA, 1992) p. 33.Google Scholar
33.Flinn, P.A., in Reference 12, p. 3.Google Scholar
34.Budhani, R.C., Bunshah, R.F., and Flinn, P.A., Appl. Phys. Lett. 52 (1988) p. 284.CrossRefGoogle Scholar