Nanoparticles are often used for both metals and non-metals, in cosmetics, home appliances, electrical products, as well as paints and inks. Nanoparticles are commonly produced by the vapor phase method or the liquid phase method. However, it is still difficult to produce nanoparticles with complicated shapes, such as raspberry-shaped particles. In this study, we demonstrated that nano-raspberry particles can be made by coating the surface of the small- and the large-sized silica nanoparticle with a reactive, chemically adsorbed, monomolecular film and then by bonding the smaller nanoparticles to the surface of the larger nanoparticle. Furthermore, by preparing a fractal surface structure on a flat substrate surface, a super-water and oil repellent surface, which can potentially improve the application performance, was successfully produced.

The influence of low curing temperatures (5, 10 and 15 ± 2 °C) on the strength and durability properties of ground granulated blastfurnace slag (GGBS) and ground granulated Corex slag (GGCS) concretes was studied. A standard curing temperature of 23 ± 2 °C) was also used for comparative purposes. Test specimens were cast using 100% CEM I 52.5N (PC), and three PC/Slag (GGBS or GGCS) replacement ratios of 50/50, 65/35 and 80/20, and a w/b ratio of 0.40. The specimens were cured for 28 days by submersion in water at the respective curing temperatures and then tested for durability. Durability was assessed using oxygen permeability, water sorptivity and chloride conductivity tests. The results showed that durability of the concretes decreased as the curing temperature decreased – gas permeability and water sorptivity increased while chloride resistance decreased. It was also observed that at a given curing temperature, the slag blended concretes showed superior durability performance than the plain PC concretes.

Ceria (CeO2) possesses a distinctive redox property due to a reversible conversion to its nonstoichiometric oxide and has been considered as a promising catalyst in the oxidative coupling of methane. Since a heterogeneously catalytic process usually takes place only on the surface of catalysts, it is reasonably expected that the performance of a catalyst, such as CeO2, highly relies on its size- and shape-dependent surface structure. We report our recent progress in achieving exclusive crystal facet-terminated CeO2 nanocrystals using a shape-controlled synthesis protocol in a one-pot colloidal system. We modified a two-phase solvothermal approach to fabricate cubic and truncated octahedral CeO2 nanocrystals with a size-control. During the two-phase solvothermal process, we propose that the Ce-precursors transfer from the aqueous layer to the interface of the organic phase, promoted by the capping ligands (as known as phase-transfer catalysts), for the oxidation and nucleation, and subsequently form CeO2 nanocrystals in the organic layer. As different capping ligands favor binding on diverse crystal facets, tuning the composition of the capping ligand with a precise control could generate nanocrystals that are dominated by a single type of facets with a relatively narrow size distribution.

The Reaction Centers (RCs) proteins are membrane proteins representing the key component so flight energy transduction in photosynthetic organisms. Upon photon absorption, these photoenzymes produce a long lasting intra protein hole electron couples whose charges are separated by 3 nanometers. The dipoles formed within the RCs can be effectively employed as transducing cores of several biological-organic hybrid devices whose design can accomplish photocurrents generation or act as phototransistor. To widen the application of the RCs to as many substrate as possible one valuable strategy is the bioconjugation of the protein with specific molecules ad-hoc selected to improve enzymatic performance and/or integration in proper scaffolding. In the present manuscript, we investigate the changes of the isoelectric point of the RC from the carotenoidless strain of the photosynthetic bacterium Rhodobacter sphaeroides R26 by inducing “in silico” mutations to predict on the role of the aminoacids involved in the bioconjugation.

Equimolar mixtures of zero-dimensional graphene (SkySpring Nanomaterials, 1-5 nm particle size) and zinc ferrite nanoparticles (Alfa Aesar, 50 nm particle size) were exposed to mechanochemical activation by high-energy ball milling for time intervals of 0-12 hours. Their structural and magnetic properties were analyzed by Mӧssbauer spectroscopy and magnetic measurements. The spectra of zinc ferrite milled without graphene were fitted with one quadrupole-split doublet (quadrupole splitting 0.5 mm/s, isomer shift 0.23 mm/s) and indicated that zinc ferrite was superparamagnetic. The line width of the doublet increased from 0.41 to 0.64 mm/s, which correlates with a reduction in particle size as effect of the ball milling processing performed. When graphene was added to the milling powders, the Mӧssbauer spectra showed the appearance of another quadrupole doublet, with a quadrupole splitting of 0.84 mm/s and an isomer shift of -0.38 mm/s. Its abundance to the spectrum remained constant to 4.48% while the milling time was increased. This second doublet could be related to carbon atoms occupying neighborhoods in the proximity of iron atoms. Hysteresis loops were recorded in an applied magnetic field of 5 T at a temperature of 5 K. A change in the approach to saturation of the loop was observed, with saturation being achieved for the sample milled for 12 hours with graphene. Zero-field-cooling-field-cooling (ZFC-FC) was performed on all samples between 5-300 K with an applied magnetic field of 200 Oe. Graphene was found to stabilize the magnetic properties of the milled system of powders to a blocking temperature of about 90 K.

Copper is a commonly used interconnect metal in microelectronic interconnects due to its exceptional electrical and thermal properties. Particularly in applications of the 2.5 and 3D integration, Cu is utilized in through-silicon-vias (TSVs) and flip chip interconnects between microelectronic chips for providing miniaturization, lower power and higher performance than current 2D packaging approaches. SnAg capped Cu pillars are a common high-density interconnect technology for flip chip bonding. For these interconnects, specific properties of the Cu surface, such as roughness and cleanliness, are an important factor in the process to ensure quality solder bumps. During electroplating, tight processing parameters must be met so that defects are avoided, and high bump uniformity is achieved. An understanding of the interactions at the solder and Cu pillar interface is needed, based on the electroplating parameters, to determine the best method for populating solder on the wafer surface. In this study, surface treatment techniques such as oxygen plasma cleaning were performed on the Cu surfaces and the SnAg plating chemistry for depositing the solder were evaluated through hull cell testing to qualitatively determine the range of current densities to investigate. It was observed that current density while plating played a large role in solder bump deposition morphology. At the higher current densities greater than 60 mA/cm2, bump height non-uniformity and dendritic growth are observed and at lower current densities, less than or equal to 60 mA/cm2, uniform, continuous bump height occurred.

Silicon nanowires (SiNWs) were comprehensively characterized in dependence on conditions of their formation via metal (Ag) -assisted chemical etching (MACE) of monocrystalline Si. The Ag structures remained on/between SiNWs based on both n- and p-Si were found to promote surface enhancement of Raman scattering (SERS) from organic molecules adsorbed on their surface. The Ag structures on/between the SiNWs/p-Si facilitated two times higher SERS-signal from 10-6 M rhodamine 6G than those in the SiNWs/n-Si. The activity of the SERS-substrates based on p-Si was improved by modification with small Au dendrites, which provided rich family of hot spots and prevented degradation of the SERS-activity observed for pure Ag dendrites due to formation of Ag2S during one week of storage in air. The SERS-substrates based on the Au/Ag dendrites on SiNWs/p-Si allowed to achieve nanomolar detection limit of rhodamine 6G and 5,5′-dithiobis (2-nitrobenzoic acid).

In this work, lead halide perovskite photodetectors were fabricated by a laser-assisted rapid fabrication method. A microchannel was engraved on an indium tin oxide (ITO) coated polyethylene terephthalate (PET) conductive flexible substrate using a CO2 laser source. The channels were filled by methylammonium lead halide perovskite (CH3NH3PbI3) using the capillary motion of perovskite first-step method precursor. CYTOP and the low-cost commercially available FluroPel were used as a top protective coating layer to suppress the decomposition of the perovskite channel. X-ray diffraction pattern (XRD) was used to measure the stability of the perovskite. Strong humidity resistant and self-healing behavior were observed in both devices. The performance of the photodetectors was compared by measuring electrical and optical characteristics over time. This study will help in the low-cost fabrication of perovskite-based devices.

Advances in the fabrication and characterization of polymeric nanomaterials has greatly advanced the miniaturization of soft actuators, creating materials capable of replicating the functional physical behavior previously limited to the macroscale. Here, we demonstrate how a reversible shape-memory polymer actuation can be generated in a single micro/nano object, where the shape change during actuation of an individual fiber can be dictated by programming using an AFM-based method. Electrospinning was used to prepare poly(ε-caprolactone) micro-/nanofibers, which were fixed and crosslinked on a structured silicon wafer. The programming as well as the observation of recovery and reversible displacement of the fiber were performed by vertical three point bending, using an AFM testing platform introduced here. A plateau tip was utilized to improve the stability of the fiber contact and working distance, enabling larger deformations and greater rbSMPA performance. Values for the reversible elongation of εrev = 3.4 ± 0.1% and 10.5 ± 0.1% were obtained for a single micro (d = 1.0 ± 0.2 μm) and nanofiber (d = 300 ± 100 nm) in cyclic testing between the temperatures 10 and 60 °C. The reversible actuation of the nanofiber was successfully characterized for 10 cycles. The demonstration and characterization of individual shape-memory nano and microfiber actuators represents an important step in the creation of miniaturized robotic devices capable of performing complex physical functions at the length scale of cells and structural component of the extracellular matrix.

Graphene Carbon Quantum Dots (GCQDs) are multi-layered carbon nanostructures that have attracted considerable attention due to its unique properties. Many technological applications, such as batteries, biological imaging, capacitors, solar cells, light emitting diodes, among others, could benefit from the low toxicity and the chemical and physical stability of these nanostructures. Despite much research, many optical properties, such as absorption and photoluminescence, of GCQDs are not completely understood yet. GCQD absorption spectra show a number of different bands whose origin is still on discussion. Many interpretations are made considering a single graphene layer. In this work, GCQD samples synthesized by the pyrolysis of citric acid was characterized by absorption spectroscopy measurements and Density Functional Theory simulations considering multi-layered structures. Density of States and electronic response functions calculations were also performed. From the results of these calculations, the absorption band associated to a π-π* (CC) transition could be also associated to a transition between different graphene layers.

Ferroelectrics and related materials (e.g., non-traditional ferroelectrics such as relaxors) have long been used in a range of applications, but with the advent of new ways of modeling, synthesizing, and characterizing these materials, continued access to astonishing breakthroughs in our fundamental understanding come each year. While we still rely on these materials in a range of applications, we continue to re-write what is possible to be done with them. In turn, assumptions that have underpinned the use and design of certain materials are progressively being revisited. This perspective aims to provide an overview of the field of ferroelectric/relaxor/polar-oxide thin films in recent years, with an emphasis on emergent structure and function enabled by advanced synthesis, processing, and computational modeling.

Computational modeling is an important aspect of the research on nuclear waste materials. In particular, atomistic simulations, when used complementary to experimental efforts, contribute to the scientific basis of safety case for nuclear waste repositories. Here we discuss the state-of-the-art and perspectives of atomistic modeling for nuclear waste management on a few cases of successful synergy of atomistic simulations and experiments. In particular, we discuss here: (1) the potential of atomistic simulations to investigate the uranium oxidation state in mixed-valence uranium oxides and (2) the ability of cementitious barrier materials to retain radionuclides such as 226Ra and 90Sr, and of studtite/metastudtite secondary peroxide phases to incorporate actinides such as Np and Am. The new contribution we make here is the computation of the incorporation of Sr by C-S-H (calcium silicate hydrate) phases.

Applying the Green's function based code FEFF to 5f derived features in actinide materials is potentially a very rewarding endeavor. However, there are some limitations that must be addressed. As part of the effort to quantify this process, FEFF has been applied to a few simplified 4f systems. The preliminary results of this investigation are discussed below.

Boron nitride nanotubes (BNNTs) and hexagonal boron nitride platelets (h-BNs) have received considerable attention for aerospace insulation applications due to their exceptional chemical and thermal stability. Presently, making BN nanomaterials compatible with polymer and composite matrices is challenging. Due to their inert and highly stable structure, h-BN and BNNTs are difficult to covalently functionalize. In this work, we present a novel sonochemical technique that enables covalent attachment of fluoroalkoxy substituents to the surface of BN nanomaterials in a controlled and metered process. Covalent functionalization is confirmed via colloidal stability analysis, FT-IR, and x-ray photoelectron spectroscopy (XPS).

RNA delivery into deep tissues with dense extracellular matrix (ECM) has been challenging. For example, cartilage is a major barrier for RNA and drug delivery due to its avascular structure, low cell density and strong negative surface charge. Cartilage ECM is comprised of collagens, proteoglycans, and various other noncollagneous proteins with a spacing of 20nm. Conventional nanoparticles are usually spherical with a diameter larger than 50-60nm (after cargo loading). Therefore, they presented limited success for RNA delivery into cartilage. Here, we developed Janus base nanotubes (JBNTs, self-assembled nanotubes inspired from DNA base pairs) to assemble with small RNAs to form nano-rod delivery vehicles (termed as “Nanopieces”). Nanopieces have a diameter of ∼20nm (smallest delivery vehicles after cargo loading) and a length of ∼100nm. They present a novel breakthrough in ECM penetration due to the reduced size and adjustable characteristics to encourage ECM and intracellular penetration.

Thermoelectric (TE) materials, or materials that can generate an electrical energy from temperature gradient, are promising for renewable energy technology. One fundamental aspect in the TE research is the demand to maximize the TE power-factor, PF = S2 σ, by having as large Seebeck coefficient (S) and electrical conductivity (σ) as possible. In the early 90s, Hicks and Dresselhaus proposed the PF enhancement by using low-dimensional materials, in which electrons are confined in certain directions and they move freely in the other directions. This quantum effect is known as the confinement length (L) effect, in which L is the thickness or diameter of the two-dimensional (2D) or one-dimensional materials, respectively. However, a key challenge is to understand the critical value of L, at which the PF can be significantly enhanced. Recently, we reevaluated the confinement theory of the low-dimensional materials to solve this issue. We showed that electrons are fully confined only when L is smaller than an intrinsic length Λ, the so-called thermal de Broglie wavelength, which depends on the materials and can be experimentally measured. Monolayer 2D materials naturally satisfy the condition of L < Λ since their confinement length is ∼ 1 nm, while their thermal de Broglie wavelength is ∼ 5-10 nm. Therefore, they could be a good candidate for TE materials. In this review article, we first review the TE materials with low dimensions. Then, we show the basic concept of the confinement effect and the consequence of such an effect. Finally, based on this effect, we turn our attention to the progress achieved recently in the TE properties of the 2D materials such as monolayer InSe, GaN electron gas, and SrTiO3 superlattices.

Salt cake radioactive waste is a remnant solid salt concentrate after deep evaporation of radioactive evaporator concentrate at WWER NPP’s. The traditional cementing of borate-containing liquid radioactive waste, to which the salt cake belongs, leads to a significant increase in the volume of the final product. This work describes borosilicate vitreous wasteforms developed to immobilize radioactive salt cake waste and comprises data on both glass synthesis and characterization. The composition of glass selected for the purpose of immobilisation of the salt cake radioactive waste allows to include up to 40 wt. % of the oxides contained in the salt cake and to reduce the volume of the final product by more than 2 times compared with the cement compound. The batches were melted in a cold crucible melter at 1200 °C. The normalized cesium leaching rate of the vitrified wasteform product was within range 3.0·10-5 – 3.7·10-6 g/(cm2·day).

Ultraviolet germicidal irradiation (UVGI) N95 filtering facepiece respirator (FFR) treatment is considered an effective decontamination approach to address the supply shortage of N95 FFRs during the ongoing Covid-19 pandemic. In this study, we investigated the nanomechanical and topographic properties of filtration fibers that have been exposed to different doses of UVC radiation. UVC exposure was shown to decrease both Young's modulus (E), hardness (H) and fiber width, as measured on individual polypropylene (PP) fibers. Our results also show that the PP microfiber layer loses its strength when N95 respirators are exposed to an accumulated UVC dose during the process of decontamination, and the PP fiber width also exhibits a logarithmic decrease during UVC exposure. The nanoscale measurement results on individual fibers suggest that maximum cycles of UVC disinfection treatment should be limited due to excessive accumulated dose, which has the potential to decrease the fiber breaking strength.

Millimetre UO2 single crystals were cut and oriented at JRC Karlsruhe. The orientation of each face of the parallelepiped single crystals was determined with Laue diffraction and the corresponding surface area by geometric measurements. Then, the (111), (100), (110) faces of each single crystal were polished to optical grade and characterized by XRD in order to confirm the surface orientation. The dissolution of the three single crystals was achieved in nitric acid media under dynamic conditions, at room temperature. Two dissolution regimes were observed for all samples. The normalized dissolution rate measured in the first step was not influenced by the crystallographic orientation of the faces. However, during the second step, (110) oriented faces were found to dissolve 4 times faster than the (100) faces. One explanation could involve the atomic composition of each oriented surface in the fluorite-type structure