Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-09T09:07:12.075Z Has data issue: false hasContentIssue false
  • English
  • Français

Non-Destructive Investigation of Dispersion, Bonding, and Thermal Properties of Emerging Polymer Nanocomposites Using Close-Up Lens Assisted Infrared Thermography

Published online by Cambridge University Press:  17 February 2020

Ali Ashraf Open the ORCID record for Ali Ashraf [Opens in a new window] ,
Nikhil Jani ,
Francis Farmer  and
Jennifer K. Lynch-Branzoi
Ali Ashraf*
Affiliation:
Materials Science and Engineering Department, Rutgers University
Nikhil Jani
Affiliation:
Materials Science and Engineering Department, Rutgers University
Francis Farmer
Affiliation:
Materials Science and Engineering Department, Rutgers University
Jennifer K. Lynch-Branzoi
Affiliation:
Materials Science and Engineering Department, Rutgers University
*
*(Email: [email protected])
Get access

Abstract

Polymer nanocomposites possess unique sets of properties that make them suitable for different applications, including structural and flame-retardant material, electromagnetic wave reflector, sensors, thin film transistor, flexible display, and many more. The properties of these nanocomposite are dependent on nanofiller dispersion and bonding with polymer matrix (i.e. particle-matrix interaction). Thermography is a non-destructive method that may be used to gain insight into dispersion and particle-matrix interaction. Infrared (IR) radiation emitted from these nanomaterial polymer composite depends on the emissivity of the individual components. In addition, during flash heating and cooling, different thermal conductivity of components in the nanocomposite can influence pixel intensity differently in the IR image or video being captured. We have used an economical mid wavelength IR camera Fluke RSE600 equipped with a close-up macro lens and algorithm based on MATLAB image processing toolbox to analyse dispersion, voids and thermal diffusivity of patented graphene polymer nanocomposite materials (G-PMC) in micro-scale. These G-PMCs can act as a standard material to determine the potential of our IR thermography technique due to their homogeneity and lack of impurity due to unique fabrication process. Thermal diffusivity and dispersion of nanoparticles in our G-PMCs was estimated after irradiation with a xenon flash lamp by spatially mapping transient IR radiations from different G-PMCs using the Fluke RSE600 thermal imager. Results from thermography experiments were compared with scanning electron microscope (SEM) and Raman spectroscopy results. Micro-scale thermography was able to detect millimetre scale thermal diffusivity variation in the injection molded G-PMC samples and relate it to change in dispersion of nanofillers, unlike SEM and Raman, where micro-scale measurements could not determine the reason behind millimetre scale property variation. We believe this low cost, fast, micro-scale, non-destructive technique will provide valuable insight into functional polymer nanocomposite fabrication and corresponding electrical and thermal properties.

Keywords

graphenecompositemicroscalepolymer
Type
Articles
Information
MRS Advances , Volume 5 , Issue 14-15: Soft Materials and Biomaterials , 2020 , pp. 735 - 742
Check for updates
Copyright
Copyright © Materials Research Society 2020

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Cho, E.-C., Huang, J.-H., Li, C.-P., Chang-Jian, C.-W., Lee, K.-C., Hsiao, Y.-S. and Huang, J.-H., Carbon 102, 66-73 (2016).CrossRefGoogle Scholar
Song, P., Cao, Z., Cai, Y., Zhao, L., Fang, Z. and Fu, S., Polymer 52 (18), 4001-4010 (2011).CrossRefGoogle Scholar
Kim, H., Abdala, A. A. and Macosko, C. W., Macromolecules 43 (16), 6515-6530 (2010).CrossRefGoogle Scholar
Versavaud, S., Regnier, G., Gouadec, G. and Vincent, M., Polymer 55 (26), 6811-6818 (2014).CrossRefGoogle Scholar
Wu, H., Feng, L., Jiang, A. and Zhang, B., Polymer journal 43 (11), 930 (2011).CrossRefGoogle Scholar
Wieme, T., Duan, L., Mys, N., Cardon, L. and D’hooge, D., Polymers-Basel 11 (1), 87 (2019).CrossRefGoogle Scholar
Kim, H. S., Bae, H. S., Yu, J. and Kim, S. Y., Sci Rep-Uk 6 (2016).Google Scholar
Thomas, S., Rouxel, D. and Ponnamma, D., Spectroscopy of polymer Nanocomposites. (William Andrew, 2016).Google Scholar
Gresil, M., Wang, Z., Poutrel, Q.-A. and Soutis, C., Sci Rep-Uk 7 (1), 5536 (2017).CrossRefGoogle Scholar
Nosker, T., Lynch, J., Hendrix, J., Kear, B., Chiu, G., & Tse, S. (2018). U.S. Patent No. 9,896,565. Washington, DC: U.S. Patent and Trademark Office.Google Scholar
ASTM E1461‐13. (2013). Standard Test Method for Thermal Diffusivity by the Flash Method.Google Scholar
ASTM D4496-04. (2004). Standard Test Method for DC Resistance or Conductance of Moderately Conductive Materials.Google Scholar
Pena, M. and Rapún, M.-L., Advances in Mathematical Physics 2019 (2019).CrossRefGoogle Scholar
Godin, A., Palomo del Barrio, E., Morikawa, J. and Duquesne, M., J Appl Phys 124 (8), 085111 (2018).CrossRefGoogle Scholar