Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-19T20:18:25.678Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of substrate roughness on the adhesion and tribological performance of Titanium Nitride coating on AISI H13 steel

Published online by Cambridge University Press:  09 October 2018

Ricardo Ortega-Álvarez ,
María T. Hernández-Sierra ,
Benjamín Arroyo-Ramírez ,
Luis D. Aguilera-Camacho ,
J. S. García-Miranda  and
Karla J. Moreno
Ricardo Ortega-Álvarez
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
María T. Hernández-Sierra
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
Benjamín Arroyo-Ramírez
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
Luis D. Aguilera-Camacho
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
J. S. García-Miranda
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
Karla J. Moreno*
Affiliation:
Tecnológico Nacional de México/Instituto Tecnológico de Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México
*
*(Email: [email protected])
Get access

Abstract

The aim of this research was to investigate the influence of substrate roughness on the adhesion and tribological performance of thin TiN coatings obtained by physical vapor deposition. For that purpose, substrates of AISI H13 steel with surface finishes of 0.06, 0.28 and 0.90 μm in Ra were coated with TiN under the same coating conditions. The chemical composition of the steel, as well as that of the TiN coating, were obtained using EDS analysis. Adhesion tests were carried out following the procedure of BSi 1071-8 standard while hardness was evaluated by ASTM C 1327-03. On the other hand, dry sliding friction tests were conducted with a pin-on-disk tribometer, according to the ASTM G 99-05 standard. This study showed that the roughness of the coating increases as the substrate roughness increases. Regarding adhesion and hardness, all the samples showed an adhesion class 1 according to the standard and a hardness value of 14.51 GPa. Nevertheless, the highest substrate roughness produced the best adhesion. On the other hand, the lowest values for the friction coefficient and wear behavior were obtained by the sample with the lowest substrate roughness of 0.06 µm. In addition, it was found that friction and wear increase when the substrate roughness increases.

Keywords

ceramiccoatingsteeladhesiontribology
Type
Articles
Information
MRS Advances , Volume 3 , Issue 62: International Materials Research Congress XXVII , 2018 , pp. 3669 - 3674
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Al-Qawabeha, U. F., IJSER 8(2), 100–104 (2017).Google Scholar
Aguilera Camacho, L. D., García Miranda, J. S. and Moreno, K. J., J. Iron Steel Res. Int. 24, 823829 (2017).CrossRefGoogle Scholar
Miletić, A., Terek, P., Kovačević, L., Vilotić, M., Kakaš, D., Škorić, B. and Kukuruzović, D., J. Braz. Soc. Mech. Sci. Eng. 36, 293–299 (2014).CrossRefGoogle Scholar
Brostow, W., Lohse, S., Osmanson, A.T., Tobola, D. and Weathers, D.L., MRS Commun. 8(1), 178182 (2018).CrossRefGoogle Scholar
Bahri, A., Guermazi, N., Elleuch, K., and Ürgen, M., Wear 342-343, 77–84 (2015).CrossRefGoogle Scholar
Ali, M., Hamzah, E., Qazi, I. A. and Toff, M. R. M., Curr. Appl. Phys. 10, 471–474 (2010).CrossRefGoogle Scholar
Takadoum, J. and Bennani, H. H., Surf. Coat. Tech. 96, 272–282 (1997).CrossRefGoogle Scholar
Brostow, W., Deborde, J. L., Jaklewicz, M. and Olszynski, P., J. Mater. 25, 119–132(2003).Google Scholar
Brostow, W., Kovacevic, V. and Vrsaljko, D., Whitworth, J., J. Mater. 32, 273–290 (2010).Google Scholar
Brostow, W. and Hagg Lobland, H. E., Materials: Introduction and Applications, (John Wiley & Sons, New York, 2017) pp. 391–421.Google Scholar
Konca, E., Cheng, Y. T., Weiner, A. M., Dasch, J. M., Erdemir, A., and Alpas, A. T., Surf. Coat. Tech. 200, 2260–2270 (2005).CrossRefGoogle Scholar