Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-19T05:23:35.697Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication, Thermo-Mechanical Processing and Characterization of a Ti-6% Al-1.5% V-1.0 Mo-0.5% Zr-0.1% C Alloy with Addition of Ru and Modifications of Small Amounts of V and Mo

Published online by Cambridge University Press:  18 October 2019

Bayron Santoveña ,
Arnoldo Bedolla-Jacuinde  and
Francisco V. Guerra
Bayron Santoveña*
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México
Arnoldo Bedolla-Jacuinde
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México
Francisco V. Guerra
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México
*
*(Email: [email protected])
Get access

Abstract

Pseudo-α or near-α titanium alloys are being widely used in the power generation industry due to their stability at high temperature service, good mechanical characteristics and corrosion resistance. Particularly Ti-6% Al-1.5% V-1.0Mo-0.5% Zr-0.1% C alloy is mainly used in turbines components, heat exchangers and pipes for steam conduction, among others; these are subjected to critical conditions of temperature, abrasion and corrosive environments. A good performance of such devices depends on the chemistry and of the material processing story.

Effects on microstructure and wear resistance with the addition of Ru and small variation of V and Mo amounts in the Ti-6% Al-1.5% V-1.0Mo-0.5% Zr-0.1% C alloy were analyzed. Three different alloys were melted in a vacuum induction furnace with a cooled copper skull under an argon protective atmosphere for this study

Four alloys were melted “Alloy 1” Ti-6% Al-1.5% V-1.0Mo-0.5% Zr-0.1% C-0.3% Ru, “Alloy 2” Ti-6%Al-0.5%V-1.6%Mo-0.5%Zr-0.1% C-0.3% Ru, “Alloy 3” Ti-6%Al-2.2%V-0.5%Mo-0.5%Zr-0.1%C-0.3%Ru. After melting, all alloys were homogenized at 1200°C for two hours, followed by hot rolling above β transition temperature with a reduction of 50% in thickness.

All alloys were analyzed by using scanning electron microscopy (SEM) and Vickers Micro hardness (HV). Results shown that Mo and V variations modified the micro hardness by microstructure refinement. In contrast, the addition of Ru showed no microstructure modification.

Keywords

Tihardnessmicrostructurehot pressing
Type
Articles
Information
MRS Advances , Volume 4 , Issue 57-58: International Materials Research Congress XXVIII , 2019 , pp. 3097 - 3104
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Christoph, L. and Manfred, P., “Titanium and Titanium Alloys,” Fundamentals and Applications, ed. WILEY-VCH Verlang GmbH & Co. KGaA (Weinheim 2003).Google Scholar
Leonov, V. P., Gorynin, I. V., Kudryavtsev, A. S., Ivanova, L. A., Travin, V. V. and Lysenko, L. C., Appl. Res, 6(6), 580-590. (2015).Google Scholar
Liang, S. X., Feng, Z. H., Yin, L. X., Liu, X. Y., Ma, M. Z. and Liu, R. P., J. of Alloys Comp, 664, 11-18 (2016).CrossRefGoogle Scholar
Biesiekierski, A., Ping, D. H., Yamabe-Mitarai, Y. and Wen, C.. Mater. & Desg, 59, 303-309 (2014).CrossRefGoogle Scholar
Gorynin, I. V., Mater. Sci. Engr, A.263(2), 112-116. (1999).CrossRefGoogle Scholar
Ehtemam-Haghighi, S., Prashanth, K.G., Attar, H., Chaubey, A.K., Cao, G.H. , Zhang, L.C.. Mater. Desg, 111, 592–599 (2016).CrossRefGoogle Scholar
Li, W., Chena, Z., Liua, J., Zhua, S., Suia, G., Wanga, Q., J. Mater. Sci. Tec, 35, 790–798 (2019).CrossRefGoogle Scholar