Hostname: page-component-586b7cd67f-l7hp2 Total loading time: 0 Render date: 2024-11-20T09:21:29.891Z Has data issue: false hasContentIssue false
  • English
  • Français

Dry sliding wear of a Ni-based superalloy as a function of the aging time.

Published online by Cambridge University Press:  26 November 2020

Luis E. Gonzalez A. ,
Arnoldo Bedolla-Jacuinde ,
Eduardo Cortés C ,
Francisco V. Guerra  and
A Ruiz
Luis E. Gonzalez A.
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
Arnoldo Bedolla-Jacuinde*
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
Eduardo Cortés C
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
Francisco V. Guerra
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
A Ruiz
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
*
*Corresponding author: [email protected]
Get access

Abstract

From the present work, the wear behavior of aged Ni-based superalloy was analyzed under dry sliding conditions. Such alloy was melted in a vacuum induction furnace and cast into a ceramic mold. Then the alloy was solubilized at 1080°C for 4 hours and then aged at 760°C for 4, 8, 16, 24, 48, 72 and 150 hours. The alloy was characterized as-cast and also in the heat-treated conditions by transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Mechanical characterization included just Vickers hardness and wear resistance under dry sliding conditions by a block on ring configuration according to the ASTM G77 standard. Wear tests were undertaken for 2000 m at a speed of 0.7 ms-1 at two different loads (25 and 78 N). The worn samples were analyzed by an optical profiler to determine the wear volume and by SEM to analyze the worn surface and the microstructure below the worn surface. The main findings indicate the formation of an oxide layer mainly formed by Cr and Ni during sliding. The thickness of such a layer is about 10 μm for short aging times and about 5 μm for longer aging times. For this load, the wear resistance was 50% higher for the shorter aging times than that for the longer aging times. This behavior is described in terms of the thickness of the protecting layer, and on the availability of chromium to form such a layer since it forms Cr23C6 at long aging times. On the other hand, for a load of 78 N the wear behavior is in agreement with hardness. Wear resistance increases with aging time due to the higher precipitation of prime gamma phase.

Type
Articles
Information
MRS Advances , Volume 5 , Issue 59-60: International Materials Research Congress XXIX , 2020 , pp. 3091 - 3102
Check for updates
Copyright
Copyright © The Author(s), 2020, published on behalf of Materials Research Society by Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Hardwicke, C.U. and Lau, Y.-C., Advances in Thermal Spray Coatings for Gas Turbines and Energy Generation: A Review. Journal of Thermal Spray Technology, 22(5) (564-576) 2013.CrossRefGoogle Scholar
Tawancy, H.M. and Al-Hadhrami, L.M., Comparative performance of turbine blades used in power generation: Damage vs. microstructure and superalloy composition selected for the application. Engineering Failure Analysis, 46 (76-91) 2014.CrossRefGoogle Scholar
Stoyanov, P., Dawan, L., Goberman, D., and Shah, D., Friction and Wear Characteristics of Single Crystal Ni-Based Superalloys at Elevated Temperatures. Tribology Letters, 66(1) (47-52) 2018.CrossRefGoogle Scholar
Xin, L., Yang, B., Wang, Z., Li, J., Lu, Y., and Shoji, T., Effect of normal force on fretting wear behavior and mechanism of Alloy 690TT in high temperature water. Wear, 368-369 (210-218) 2016.Google Scholar
Xin, L., Yang, B., Wang, Z., Li, J., Lu, Y., and Shoji, T.,, Microstructural evolution of subsurface on Inconel 690TT alloy subjected to fretting wear at elevated temperature. Materials & Design, 104 (152-161) 2016.CrossRefGoogle Scholar
Benea, L., Basa, S., Danaila, E., Caron, N., Raqquet, O., Ponthioux, P., and Celis, J.P., Fretting and wear behaviors of Ni/nano-WC composite coatings in dry and wet conditions. Materials & Design (1980-2015), 65 (550-558) 2015.CrossRefGoogle Scholar
Chung, I. and Lee, M., An experimental study on fretting wear behavior of cross-contacting Inconel 690 tubes. Nuclear Engineering and Design, 241(10) (4103-4110) 2011.CrossRefGoogle Scholar
Li, J., Lu, Y., Zhang, H., and Xin, L., Effect of grain size and hardness on fretting wear behavior of Inconel 600 alloys. Tribology International, 81 (215-222) 2015.CrossRefGoogle Scholar
Heredia, S. and Fouvry, S., Introduction of a new sliding regime criterion to quantify partial, mixed and gross slip fretting regimes: Correlation with wear and cracking processes. Wear, 269(7) (515-524) 2010.CrossRefGoogle Scholar
Wang, Z.H., Lu, Y.H., Li, J., and Shoji, T., Effect of pH value on the fretting wear behavior of Inconel 690 alloy. Tribology International, 95 (162-169. 2016.CrossRefGoogle Scholar
Thirugnanasambantham, K.G. and Natarajan, S., Mechanistic studies on degradation in sliding wear behavior of IN718 and Hastelloy X superalloys at 500°C. Tribology International, 101(324-330) 2016.CrossRefGoogle Scholar
Mi, X., Cai, Z., Xiong, X., Qian, H., Tang, L., Xie, Y., Peng, J., and Zhu, M., Investigation on fretting wear behavior of 690 alloy in water under various temperatures. Tribology International, 100 (400-409) 2016.CrossRefGoogle Scholar
Okazaki, M., High-temperature strength of Ni-base superalloy coatings. Science and Technology of Advanced Materials, 2(2) (357-366) 2001.CrossRefGoogle Scholar
Andrieu, E., Molins, R., Ghonem, H., and Pineau, A., Intergranular crack tip oxidation mechanism in a nickel-based superalloy. Materials Science and Engineering: A, 154(1) (21-28) 1992.CrossRefGoogle Scholar
Stott, H., C, F.. Stevenson, W., and Wood, G. C., Friction and wear properties of Stellite 31 at temperatures from 293 to 1073K. Metals and Technology, 4 (66-74) 1977.CrossRefGoogle Scholar
Glascott, J., Stott, F.H., and Wood, G.C., The effectiveness of oxides in reducing sliding wear of alloys. Oxidation of Metals, 24(3) (99-114) 1985.CrossRefGoogle Scholar
Wang, J., Zhou, L., Sheng, L., and Guo, J., The microstructure evolution and its effect on the mechanical properties of a hot-corrosion resistant Ni-based superalloy during long-term thermal exposure. Materials & Design, 39 (55-62) 2012.CrossRefGoogle Scholar
Sidhu, T.S., Prakash, S., and Agrawal, R.D., Hot corrosion and performance of nickel-based coatings. Current Science, 90(1) (41-47) 2006.Google Scholar
Sauger, E., Ponsonnet, L., Martin, J.M., and Vincent, L., Study of the tribologically transformed structure created during fretting tests. Tribology International, 33(11) (743-750) 2000.CrossRefGoogle Scholar
Zhou, Z.R., Sauger, E., Liu, J.J., and Vincent, L., Nucleation and early growth of tribologically transformed structure (TTS) induced by fretting. Wear, 212(1) (50-58) 1997.CrossRefGoogle Scholar
Bedolla-Jacuinde, A., Guerra, F.V., Mejia, I., Zuno-Silva, J., and Rainforth, M., Abrasive wear of V–Nb–Ti alloyed high-chromium white irons. Wear, 332-333 (1006-1011) 2015.CrossRefGoogle Scholar
Cortés-Carrillo, E., Bedolla-Jacuinde, A., Mejia, I., Zepeda, C.M., Zuno-Silva, J., and Guerra-Lopez, F.V., Effects of tungsten on the microstructure and on the abrasive wear behavior of a high-chromium white iron. Wear, 376-377 (77-85) 2017.CrossRefGoogle Scholar
Holt, R.T. and Wallace, W., Impurities and trace elements in nickel-base superalloys. International Metals Reviews, 21(1) (1-24) 1976CrossRefGoogle Scholar
Qin, X.Z., Guo, J.T., Yuan, C., Chen, C.L., and Ye, H.Q., Effects of Long-Term Thermal Exposure on the Microstructure and Properties of a Cast Ni-Base Superalloy. Metallurgical and Materials Transactions A, 38(12) (3014-3022). 2007.CrossRefGoogle Scholar