Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-29T13:06:14.104Z Has data issue: false hasContentIssue false
  • English
  • Français

The use of Nano- Synthesis Methodology on Electrochemical Performance of limn2o4 Cathode at elevated Temperature

Published online by Cambridge University Press:  20 March 2018

S Mudono ,
J Tshuma ,
T.T Manhongo ,
T.C Madzokere ,
P Tsorai  and
L.K Witika
S Mudono*
Affiliation:
Department of Chemical Engineering, Faculty of Industrial Technology, National University of Science & Technology, Bulawayo, Zimbabwe
J Tshuma
Affiliation:
Department of Chemical Engineering, Faculty of Industrial Technology, National University of Science & Technology, Bulawayo, Zimbabwe
T.T Manhongo
Affiliation:
Department of Chemical Engineering, Faculty of Industrial Technology, National University of Science & Technology, Bulawayo, Zimbabwe
T.C Madzokere
Affiliation:
Department of Chemical and Process Systems Engineering, Faculty of Engineering and Technology, Harare Institute of Technology, P. O. Box BE 277, Belvedere, Harare, Zimbabwe
P Tsorai
Affiliation:
Department of Chemical and Process Systems Engineering, Faculty of Engineering and Technology, Harare Institute of Technology, P. O. Box BE 277, Belvedere, Harare, Zimbabwe
L.K Witika
Affiliation:
Department of Metallurgy, School of Mines, University of Zambia, Lusaka, Zambia
*
*Corresponding Author: Stanford Mudono, [email protected]
Get access

Abstract:

The effects of different starting materials using nano-synthesis methodology on electrochemical performance of lithium manganese oxide (LixMn2O4) are studied. Four spinel-type LixMn2O4 (LMO) cathode materials were prepared with different lithium and manganese sources and were analyzed chemically and characterized by BET and XRD. The electrochemical performance of the cathodes at room temperature and elevated temperature was tested. The crystal structure was indexed to be a cubic system with lattice parameters of 8.2342 ±0.170 Å and defined to the space group Fd3m. There was no peak of impurity because the raw materials for Mn source were first treated with acid. Although the results showed that the structures of the samples were confirmed to be cubic spinel structure, the lattice parameter and specific surface area of the samples were different. The LiMn2O4 cathodes have an initial discharge capacity of over 120mAh/g and show an ordinary two-step voltage profile. The results demonstrated that the cathode materials prepared with LiNO3 as Li source have larger lattice parameters, than those prepared from LiOH·H2O as Li source. The cathode prepared from Electrochemical Manganese Dioxide (EMD) as Mn source have larger particle sizes, lower first charge and discharge capacity, better cyclic performance, whereas those from Chemical Manganese Dioxide (CMD) as Mn source have smaller particle size, higher first charge and discharge capacity, and poor cyclic stability at elevated temperature. The cell polarization of the cathode developed by LiOH•H2O and EMD was identified to be the least and the elevated temperature cycelability to be the best. These manifestations can be attributed to differences in Li and Mn sources, specific surface areas, purities of starting materials and synthesis conditions. Melt-impregnation as a nano-synthesis method proved to be an excellent method to synthesize LiMn2O4 cathode materials that can operate at elevated temperatures when using correct starting materials and good control of synthesis temperatures.

Keywords

compositedielectric properties
Type
Articles
Information
MRS Advances , Volume 3 , Issue 42-43: African Materials Research Society 2017 , 2018 , pp. 2589 - 2602
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Sun, Yang-Kook, Oh, Bookeun, Lee, Awack Joo: Electrochim. Acta. 46, 541–546 (2001).CrossRefGoogle Scholar
Uchiyama, Takayuki, Nishizawa, Matsuhiko, Itoh, Takashi, Uchida, Isami: J.Electrochem. Soc..147(6), 2057–2060 (2000).CrossRefGoogle Scholar
Kang, Sun-Ho, Goodenough, John B: J.Electrochem. Soc..147(10), 3621–7 (2000).CrossRefGoogle Scholar
Lanz, Martin, Kormann, Claudius, Steinnger, Helmut, Heil, Gunter, Hass, Otto, Noak, Petr: J.Electrochem. Soc..147(11), 3997–4000 (2000).CrossRefGoogle Scholar
Amatucci, G.G, Pereira, N, Zheng, T, Tarscon, J.M: J.Electrochem. Soc..148 (2), A171-A182 (2001).CrossRefGoogle Scholar
Matsuo, Y, Kostecki, R, McLarnon, F: J.Electrochem. Soc.148 (7), A687-A692 (2001).CrossRefGoogle Scholar
Uchida, I, Mohamedi, M, Dokko, K, Nishizawa, M, Itoh, T, Umeda, M: J.Power.Sources 97-98, (2001).Google Scholar
Lu, Cheung-hsin, Lin, Shang-Wei: J.Power Sources 93, 14–19 (2001)CrossRefGoogle Scholar
Yoshio, Masaki,Xia, Yongyao, Kumada, Naoki, Ma, Shuihua: J.Power Sources 101, 79-85 (2001).CrossRefGoogle Scholar
Numata, Tatsuji, Amemiya, Achika, Kumeuchi, Tomokazu, Shirakata, Masato, Yonezawa, Masatomo: J.Power Sources 97-98, 358-360 (2001).CrossRefGoogle Scholar
Dokko, Kaoru, Horikoshi, Soichi, Itoh, Takashi, Nishizawa, Matsuhiko, Mohamedi, Mohamed, Uchida, Isamu: J.Power Sources 90, 109–115 (2000)CrossRefGoogle Scholar