Hostname: page-component-78c5997874-t5tsf Total loading time: 0 Render date: 2024-11-19T13:05:12.610Z Has data issue: false hasContentIssue false
  • English
  • Français

The Hydrophilic to Superhydrophilic Change Induced by Polyhydroxybutyrate in Polyethylene glycol:Polyhydroxybutyrate Electrospun Samples by Plasma Treatment

Published online by Cambridge University Press:  07 June 2016

Ma Guadalupe Rojano-Molina ,
Maraolina Domínguez-Díaz ,
Horacio Martinez-Valencia ,
José Escorcia-García  and
Ruth Fabiola Balderas-Valadez
Ma Guadalupe Rojano-Molina
Affiliation:
Facultad de Ciencias Químicas e Ingeniería, Universidad Autónoma del Estado de Morelos Av. Universidad No. 1001, Col. Chamilpa, Cuernavaca, Morelos, C.P.62209, MÉXICO
Maraolina Domínguez-Díaz*
Affiliation:
Centro de Investigación en Ingeniería y Ciencias Aplicadas, Universidad Autónoma del Estado de Morelos, Av. Universidad No. 1001, Col. Chamilpa, Cuernavaca, Morelos, C.P.62209, MÉXICO
Horacio Martinez-Valencia
Affiliation:
Instituto de Ciencias Físicas-UNAM, Av. Universidad S/N, Col. Chamilpa, Cuernavaca, Morelos, C.P.62210, MÉXICO
José Escorcia-García
Affiliation:
CONACYT-CINVESTAV del IPN, Unidad Saltillo, Industrial, Zona Industrial, Ramos Arizpe, Coahuila, C.P. 25900, MÉXICO
Ruth Fabiola Balderas-Valadez
Affiliation:
Centro de Investigación en Ingeniería y Ciencias Aplicadas, Universidad Autónoma del Estado de Morelos, Av. Universidad No. 1001, Col. Chamilpa, Cuernavaca, Morelos, C.P.62209, MÉXICO
*
*To whom correspondence should be addressed: [email protected]
Get access

Abstract

This work studied the effect of plasma treatment on the wettability of composite materials constituted of polyethylene glycol (PEG) and polyhydroxybutyrate (PHB) processed through the spin-coating and electrospinning techniques. For this purpose different polymeric solutions of PEG:PHB with proportions of 100:0, 80:20, 50:50, 20:80, and 0:100 were prepared. It found that the hydrophobicity of the as-prepared composite films processed by electrospinning was higher than those processed by spin-coating, using the same proportions of PEG:PHB. The electrospun samples with higher content of PHB (20:80 and 0:100) showed a surface morphology constituted by fibers of 1.7-1.9 μm in size. On the other hand, the electrospun samples processed with a lower content of PHB (100:0, 80:20, 50:50) did not form fibers and exhibited a rough surface. The subsequent plasma treatment with argon plasma of the electrospun samples produced a decrease in the contact angle, even in the samples with surface roughness. These contact angle values were similar to those obtained by spin-coating, or even lower, as in the case of the sample with PEG:PHB content of 20:80 in which the dip-coated film, the as-prepared membrane, and the plasma-treated membrane showed contact angles of 49°, 77.4°, and 0° (superhydrophilic) respectively.

Keywords

polymerfibermorphology
Type
Articles
Information
MRS Advances , Volume 1 , Issue 29: Soft Materials and Biomaterials , 2016 , pp. 2125 - 2131
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Pisuchpen, T., Chaim-ngoen, N., Intasanta, N., Supaphol, P. and Hoven, V.P., Langmuir 27, 3654 (2011).Google Scholar
Das, S.N., Choi, J.H., Kar, J.P., and Myoung, J.M., Applied Surface Science 255, 7319 (2009).Google Scholar
Domínguez-Díaz, M. and Cruz-Chávez, M.A., Mater. Res. Soc. Proc. 1753 (2015).CrossRefGoogle Scholar
Cheng, Q., Lee, B.L.-P., Komvopoulos, K., Yan, Z., and Li, S., Tissue Engineering:Part A 19, 1188 (2013).Google Scholar
Domínguez-Díaz, M., Meneses-Acosta, A., and Romo-Uribe, A., Mater. Res. Soc. Proc. 1721 (2015).Google Scholar
Jokinen, V., Suvanto, P., Franssila, S., Biomicrofluidics 6, 016501–1 (2014).CrossRefGoogle Scholar
Shameli, K., Mansor, B., Jazayeri, S., Sedaghat, S., Shabanzadeh, P., Jahangirian, H., and Abdollahi, Y., International Journal of Molecular Sciences, 6639 (2012).Google Scholar
Domínguez-Díaz, M., Meneses Acosta, A., Romo Uribe, A., Peña, C., Segura, D., and Espin, G., European Polymer Journal 63, 101 (2015).Google Scholar
Jacobs, T., Declercq, H., De Geyter, N., Cornelissen, R., Dubruel, P., Leys, C., Morent, R., Surface and Coatings Technology 232, 447 (2013).Google Scholar