Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-05T14:44:44.239Z Has data issue: false hasContentIssue false
  • English
  • Français

Study on Flexibility of Intracranial Vascular Stents Based on the Finite Element Method

Published online by Cambridge University Press:  28 August 2018

L. Liu ,
H. Jiang ,
Y. Dong ,
L. Quan  and
Y. Tong
L. Liu*
Affiliation:
Jiangsu Provincial Key Laboratory for Interventional Medical Devices Huaiyin Institute of Technology Huaian, China School of Mechanical Engineering Nanjing University of Science and Technology Nanjing, China
H. Jiang
Affiliation:
Faculty of Mechanical & Material Engineering Huaiyin Institute of Technology Huaian, China
Y. Dong
Affiliation:
Faculty of Mechanical & Material Engineering Huaiyin Institute of Technology Huaian, China
L. Quan
Affiliation:
Faculty of Mechanical & Material Engineering Huaiyin Institute of Technology Huaian, China
Y. Tong
Affiliation:
School of Mechanical Engineering Nanjing University of Science and Technology Nanjing, China
*
* Corresponding author ([email protected])
Get access

Abstract

Flexibility is a particularly important biomechanical property for intracranial vascular stents. To study the flexibility of stent, the following work was carried out by using the finite element method: Four mechanical models were adopted to simulate the bending deformation of stents, and comparative studies were conducted about the distinction between cantilever beam and simply supported beam, as well as the distinction between moment-loading method and displacement-loading method. A complete process as implanting a stent including compressing, expanding and bending was also simulated, for analyzing the effects of compressing and expanding deformation on stent flexibility. At the same time, the effects of the arrangement and the number of bridges on stent flexibility were researched. The results show that: 1. A same flexibility index was obtained from cantilever beam model and simply supported beam model; displacement-loading method is better than moment-loading for simulating the bending deformation of stents. 2. The flexibility of stent with compressing and expanding deformation is lower than that in the initial form. 3. Crossly arranging the neighboring bridges in axial direction, can effectively improve the stent flexibility and reduce the flexibility difference in various bending directions; the bridge number, has proportional non-linear correlation with the stent rigidity as well as the maximum moment required for bending the stent.

Keywords

Finite elementIntracranial vascular stentsFlexibilityBridges
Type
Research Article
Information
Journal of Mechanics , Volume 35 , Issue 4 , August 2019 , pp. 465 - 474
Copyright
© The Society of Theoretical and Applied Mechanics 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

De Bock, S. et al., “Our Capricious Vessels: The Influence of Stent Design and Vessel Geometry on the Mechanics of Intracranial Aneurysm Stent Deployment,” Journal of Biomechanics, 45, pp. 1353–1359 (2012).CrossRefGoogle ScholarPubMed
Pierre, B. O. B. R. O., “Particle Imaging Velocimetry Evaluation of Intracranial Stents in Sidewall Aneurysm: Hemodynamic Transition Related to the Stent Design,” Plos One, 9, pp. 1–17 (2014).Google Scholar
Barragan, P. et al., “Longitudinal Compression Behaviour of Coronary Stents: A Bench-Top Comparative Study,” EuroIntervention, 9, pp. 1454–1462 (2014).CrossRefGoogle ScholarPubMed
Ormiston, J. A. et al., “Stent Longitudinal Flexibility: A Comparison of 13 Stent Designs before and after Balloon Expansion,” Catheterization & Cardiovascular Interventions, 50, pp. 120–124 (2000).3.0.CO;2-T>CrossRefGoogle ScholarPubMed
Mori, K. and Saito, T., “Effects of Stent Structure on Stent Flexibility Measurements,” Annals of Biomedical Engineering, 33, pp. 733–742 (2005).CrossRefGoogle ScholarPubMed
Kumar, G. P. et al., “Design Considerations and Quantitative Assessment for the Development of Percutaneous Mitral Valve Stent,” Medical Engineering & Physics, 36, pp. 882–888 (2014).CrossRefGoogle ScholarPubMed
Schiavone, A., Zhao, L. G. and Abdel-Wahab, A. A., “Effects of Material, Coating, Design and Plaque Composition on Stent Deployment Inside a Stenotic Artery—Finite Element Simulation,” Materials Science and Engineering: C, 42, pp. 479–488 (2014).CrossRefGoogle ScholarPubMed
Azaouzi, M. et al., “On the Numerical Investigation of Cardiovascular Balloon-Expandable Stent Using Finite Element Method,” Computational Materials Science, 79, pp. 326–335 (2013).CrossRefGoogle Scholar
Azaouzi, M., Makradi, A. and Belouettar, S., “Numerical Investigations of the Structural Behavior of a Balloon Expandable Stent Design Using Finite Element Method,” Computational Materials Science, 72, pp. 54–61 (2013).CrossRefGoogle Scholar
Wu, W. et al., “An FEA Method to Study Flexibility of Expanded Coronary Stents,” Journal of Materials Processing Technology, 184, pp. 447–450 (2007).CrossRefGoogle Scholar
Petrini, L. et al., “Numerical Investigation of the Intravascular Coronary Stent Flexibility,” Journal of Biomechanics, 37, pp. 495–501 (2004).CrossRefGoogle ScholarPubMed
Auricchio, F. et al., “Carotid Artery Stenting Simulation: From Patient-Specific Images to Finite Element Analysis,” Medical Engineering & Physics, 33, pp. 281–289 (2011).CrossRefGoogle ScholarPubMed
Ragkousis, G. E., Curzen, N. and Bressloff, N. W., “Simulation of Longitudinal Stent Deformation in a Patient-Specific Coronary Artery,” Medical Engineering & Physics, 36, pp. 467–476 (2014).CrossRefGoogle Scholar
Beule, M. D., “Finite Element Stent Design,” Ghent University Faculty of Engineering (2008).Google Scholar
Gu, X., Yi, H., Ni, Z. and Wang, Y., “Design and Fabrication of Coronary Stent,” Journal of Southeast University (Natural Science Edition), 35, pp. 898–902 (2005).Google Scholar
Shen, X., Yi, H. and Ni, Z. H., “Finite Element Analysis of the Longitudinal Flexibility Property of Coronary Stents,” Journal of Functional Materials, 40, pp. 446–442 (2009).Google Scholar
Zheng, Q., Wei, M., You, Z., An, M. and Li, Z., “Finite Element Analysis on the Longitudinal Flexibility of the Cerebral Intra Aneurysmal Stent,” Journal of Taiyuan University of Technology,” pp. 352–356 (2015).Google Scholar
Bae, I. et al., “Mechanical Behavior and in vivo Properties of Newly Designed Bare Metal Stent for Enhanced Flexibility,” Journal of Industrial and Engineering Chemistry, 21, pp. 1295–1300 (2015).CrossRefGoogle Scholar
Shobayashi, Y. et al., “Mechanical Design of an Intracranial Stent for Treating Cerebral Aneurysms,” Medical Engineering & Physics, 32, pp. 1015–1024 (2010).CrossRefGoogle ScholarPubMed
Hu, Z. et al., “Effect of Plastic Deformation on the Evolution of Wear and Local Stress Fields in Fretting,” International Journal of Solids and Structures, 82, pp. 1–8 (2016)CrossRefGoogle Scholar
Hu, Z., “Contact around a Sharp Corner with Small Scale Plasticity,” Advances in Materials, 6, pp. 10–17 (2017).CrossRefGoogle Scholar
Hu, Z. et al., “Simulation of Wear Evolution Using Fictitious Eigenstrains,” Tribology International, 82, pp. 191–194 (2015).CrossRefGoogle Scholar