Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-22T19:57:37.542Z Has data issue: false hasContentIssue false
  • English
  • Français

Nonlinear and Temperature-Dependent Material Properties of AU/SN Alloy for Power Module

Published online by Cambridge University Press:  15 May 2017

L. L. Liao  and
K. N. Chiang
L. L. Liao
Affiliation:
Department of Power Mechanical EngineeringNational Tsing Hua UniversityHsinchu, Taiwan Electronic and Optoelectronics Research LaboratoriesIndustrial Technology Research InstituteHsinchu, Taiwan
K. N. Chiang*
Affiliation:
Department of Power Mechanical EngineeringNational Tsing Hua UniversityHsinchu, Taiwan Advanced Packaging Research CenterNational Tsing Hua UniversityHsinchu, Taiwan
*
*Corresponding author ([email protected])
Get access

Abstract

In recent years, the material Au-20Sn eutectic solder, which is resistant to high temperatures, is used for electric interconnections in high-power modules, the material properties such as temperature and strain rate dependent stress-strain curve are critically needed for reliability assessment of Au-20Sn solder joint. Thus, this study was performed to determine the material properties of Au-20Sn eutectic solder under various strain rates and temperature loads. Many researches using shear test to determine the shear resistance of solder joint, however, the mechanical strength as measured by the shear test is the maximum shear strength of the package joint, but this measurement does not represent the stress-strain behavior of Au-20Sn material. To identify the material properties of Au-20Sn eutectic solder, the tensile test was performed to measure its mechanical strength and nonlinear material properties. The strain rate effect was examined in terms of the influence of the mechanical strength on the Au-20Sn eutectic solder at different tensile rates. The temperature-dependent material properties of Au-20Sn solder were also measured under various thermal loadings, and material properties of Au-20Sn obtained in this research can be applied to the simulation model, the thermomechanical behavior and reliability of the power module can be further analyzed and evaluated.

Keywords

Au-20Sn eutectic solderHigh-power moduleMechanical strengthStress-strain curveNonlinear material propertiesTensile test
Type
Research Article
Information
Journal of Mechanics , Volume 33 , Issue 5 , October 2017 , pp. 663 - 672
Copyright
Copyright © The Society of Theoretical and Applied Mechanics 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Lu, H., Bailey, C. and Yin, C., “Design for Reliability of Power Electronics Modules,” Microelectronics Reliability, 49, pp. 1250–1255 (2009).Google Scholar
2. Hung, T. Y., Chiang, S. Y., Huang, C. J., Lee, C. C. and Chiang, K. N., “Thermal-Mechanical Behavior of the Bonding Wire for a Power Module Subjected to the Power Cycling Test,” Microelectronics Reliability, 51, pp. 1819–1823 (2011).Google Scholar
3. Yoon, S. W., Glover, M. D., Mantooth, H. A. and Shiozaki, K., “Reliable and Repeatable Bonding Technology for High Temperature Automotive Power Modules for Electrified Vehicles,” Journal of Micromechanics and Microengineerin, 23, 015017 (2013).Google Scholar
4. Lang, F., Nakagawa, H., Aoyagi, M., Ohashi, H. and Yamaguchi, H., “A Novel Chip Joint Method for High Temperature Operated SiC Power Modules,” Proceedings of the 8th Electronics Packaging Technology Conference, Singapore, pp. 597–603 (2006).Google Scholar
5. Lang, F., Hayashi, Y., Nakagawa, H., Aoyagi, M. and Ohashi, H., “A Novel Three-Dimensional Packaging Method for Al-Metalized SiC Power Devices,” IEEE Transactions on Advanced Packaging, 32, pp. 773–779 (2009).Google Scholar
6. Kanata, T., Nishiwaki, K. and Hamada, K., “Development Trends of Power Semiconductors for Hybrid Vehicles,” Proceedings of the International Power Electronics Conference, Sapporo, Japan, pp. 778–782 (2010).Google Scholar
7. Thebaud, J. M. et al., “Strategy for Designing Accelerated Aging Tests to Evaluate IGBT Power Modules Lifetime in Real Operation Mode,” IEEE Transactions on Components and Packaging Technologies, 26, pp. 429–438 (2003).Google Scholar
8. Ciappa, M., “Selected Failure Mechanisms of Modern Power Modules,” Microelectronics Reliability, 42, pp. 653–667 (2002).Google Scholar
9. Yin, C. Y., Lu, H., Musallam, M., Bailey, C. and Johnson, C. M., “A Physics-of-Failure Based Prognostic Method for Power Modules,” Proceedings of the 10th Electronics Packaging Technology Conference, Singapore, pp. 1190–1195 (2008).Google Scholar
10. Shinohara, K. and Qiang, Y., “Fatigue Evaluation of Power Devices,” Proceedings of the International Conference on Electronic Packaging Technology and High Density Packaging, Beijing, China, pp. 1277–1283 (2009).Google Scholar
11. Yu, Q., Shibutani, T., Tanaka, A., Koyama, T. and Shiratori, M., “Low-Cycle Fatigue Reliability Evaluation for Lead-Free Solders in Vehicle Electronics Devices,” Proceedings of the ASME Inter-PACK Conference, Vancouver, Canada, pp. 531–537 (2007).Google Scholar
12. Lee, N. C., “Lead-Free Soldering and Low Alpha Solders for Wafer Level Interconnects,” Proceedings of the International Conference Surface Mount Technology Association, Chicago, IL, USA, (2000).Google Scholar
13. Bernstein, L., “Semiconductor Joining by the Solid-Liquid-Interdiffusion (SLID) Process: I. The Systems Ag-In, Au-In, and Cu-In,” Journal of The Electrochemical Society, 113, pp. 1282–1288 (1966).Google Scholar
14. Jacobson, D. M. and Humpston, G., “Diffusion Soldering,” Soldering and Surface Mount Technology, 4, pp. 27–32 (1992).Google Scholar
15. Lee, C. C., Wang, C. Y. and Matijasevic, G., “Advances in Bonding Technology for Electronic Packaging,” Journal of Electronic Packaging, 115, pp. 201–207 (1993).Google Scholar
16. Okamoto, H., “Au-Sn (Gold-Tin),” Journal of Phase Equilibria and Diffusion, 28, 490 (2007).Google Scholar
17. Suganuma, K., Kim, S. J. and Kim, K. S., “High-Temperature Lead-Free Solders: Properties and Possibilities,” Journal of Mechanics, 61, pp. 64–71 (2009).Google Scholar
18. Lang, F., Nakagawa, H., Aoyagi, M., Ohashi, H. and Yamaguchi, H., “Impact of Joint Materials on the Reliability of Double-Side Packaged SiC Power Devices During High Temperature Aging,” Journal of Materials Science: Materials in Electronics, 21, pp. 917–925 (2010).Google Scholar
19. Lang, F., Hayashi, Y., Nakagawa, H., Aoyagi, M. and Ohashi, H., “Joint Reliability of Double-Side Packaged SiC Power Devices to a DBC Substrate with High Temperature Solders,” Proceedings of the 10th Electronics Packaging Technology Conference, Singapore, pp. 897–902 (2008).Google Scholar
20. Hagler, P., Johnson, R. W. and Chen, L. Y., “SiC Die Attach Metallurgy and Processes for Applications up to 500°C,” IEEE Transactions on Components and Packaging Technologies, 1, pp. 630–639 (2011).Google Scholar
21. Tollefsen, T., Larsson, A., Løvvik, O. and Aasmundtveit, K., “Au-Sn SLID Bonding-Properties and Possibilities,” Metallurgical and Materials Transactions B, 43, pp. 397–405 (2012).Google Scholar
22. Oppermann, H., The Role of Au/Sn Solder in Packaging, Springer, London, p. 377 (2005).Google Scholar
23. Anhock, S. et al., “Investigations of Au-Sn Alloys on Different End-Metallizations for High Temperature Applications [solders],” Proceedings of the 22th International Electronics Manufacturing Technology Symposium, Berlin, Germany, pp. 156–165 (1998).Google Scholar
24. Eckermann, J. et al., “Computational Modeling of Creep-Based Fatigue as a Means of Selecting Lead-Free Solder Alloys,” Microelectronics Reliability, 54, pp. 1235–1242 (2014).Google Scholar
25. Che, F. X., Zhu, W. H., Poh, E. S. W., Zhang, X. W. and Zhang, X. R., “The Study of Mechanical Properties of Sn-Ag-Cu Lead-Free Solders with Different Ag Contents and Ni Doping under Different Strain Rates and Temperatures,” Journal of Alloys and Compounds, 507, pp. 215–224 (2010).Google Scholar
26. Chen, X., Chen, G. and Sakane, M., “Prediction of Stress-Strain Relationship with an Improved Anand Constitutive Model for Lead-Free Solder Sn-3.5 Ag,” IEEE Transactions on Components and Packaging Technologies, 28, pp. 111–116 (2005).Google Scholar
27. Wang, G. Z., Cheng, Z. N., Becker, K. and Wilde, J., “Applying Anand Model to Represent the Viscoplastic Deformation Behavior of Solder Alloys,” Journal of Electronic Packaging, 123, pp. 247–253 (2001).Google Scholar
28. Liu, D. S. and Chao, Y. C., “Effects of Dopant, Temperature, and Strain Rate on the Mechanical Properties of Micrometer Gold-Bonding Wire,” Journal of Electronic Materials, 32, pp. 159–165 (2003).Google Scholar
29. Sahli, A., Boufeldja, S., Kebdani, S. and Rahmani, O., “Failure Analysis of Anisotropic Plates by the Boundary Element Methos,” Journal of Mechanics, 30, pp. 561–570 (2014).Google Scholar