Hostname: page-component-cd9895bd7-jn8rn Total loading time: 0 Render date: 2024-12-22T21:51:53.488Z Has data issue: false hasContentIssue false
  • English
  • Français

An Accurate Performance Prediction of Solid Fuel Ramjets Using Coupled Intake-Combustor-Nozzle Simulation

Published online by Cambridge University Press:  14 October 2020

A. M. Tahsini Open the ORCID record for A. M. Tahsini [Opens in a new window]
A. M. Tahsini*
Affiliation:
School of Mechanical Engineering, Iran University of Science and Technology, Tehran, IRAN
*
*Corresponding author ([email protected])
Get access

Abstract

The performance of the solid fuel ramjet is accurately predicted using full part simulation of this propulsion system, where the flow fields of the intake, combustion chamber, and the nozzle are numerically studied all together. The conjugate heat transfer is considered between the solid phase and the gas phase to directly compute the regression rate of the fuel. The finite volume solver of the compressible turbulent reacting flow is utilized to study the axisymmetric three dimensional flow fields, and two blocks are used to discretize the computational domain. It is shown that the combustion chamber's pressure is changed due to the fuel flow rate's increment which must be taken into account in predictions. The results demonstrate that omitting the pressure dependence of the regression rate and also the effect of the combustor's inlet profile on the regression rate, which specially exists when simulating the combustion chamber individually, under-predicts the solid fuel burning rate when the regression rate augmentation technique is applied to improve the performance of the solid fuel ramjets. It is also illustrated that using the inlet swirl to increase the regression rate of the solid fuel augments considerably the thrust level of the considered SFRJ, while the predictions without considering all parts of the ramjet is not accurate.

Keywords

Burning rateCombustorIntakeNozzleRamjetSolid fuelSwirlThrust
Type
Research Article
Information
Journal of Mechanics , Volume 36 , Issue 6 , December 2020 , pp. 933 - 941
Copyright
Copyright © 2020 The Society of Theoretical and Applied Mechanics

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Netzer, D. W., “Modeling Solid Fuel Ramjet Combustion,” Journal of Spacecraft and Rocket, 14, pp. 762-766 (1977).CrossRefGoogle Scholar
Schadow, K. C., Cordes, H. F., and Chieze, D. J., “Experimental Studies of Combustion Processes in a Tubular Combustor with Fuel Addition along the Wall,” Combustion Science and Technology, 19, pp. 51-57 (1978).CrossRefGoogle Scholar
Raghunandan, B. N., Ravichandran, E. R., and Marathe, A. G., “Combustion Related to Solid Fuel Ramjets,” Journal of Propulsion and Power, 1, pp. 502-504 (1985).CrossRefGoogle Scholar
Schulte, G., “Fuel Regression and Flame Stabilization Studies of Solid Fuel Ramjets,” Journal of Propulsion and Power, 2, pp. 301-304 (1986).CrossRefGoogle Scholar
Natan, B., and Gany, A., “Ignition and Combustion of Boron Particles in the Flowfield of a Solid Fuel Ramjet,” Journal of Propulsion and Power, 7, pp. 37-43 (1991).CrossRefGoogle Scholar
Ben-Arosh, R., and Gany, A., “Similarity and Scale Effects in Solid Fuel Ramjet Combustors,” Journal of Propulsion and Power, 8, pp. 615-623 (1992).CrossRefGoogle Scholar
Liou, T. M., Hwang, P. W., Li, Y. C., and Chan, C. Y., “Flame stability analysis of turbulent non-premixed reacting flow in a simulated solid-fuel ramjet combustor,” Journal of Mechanics, 18, pp. 43–51 (2002).CrossRefGoogle Scholar
Yang, J. T., Lee, S. C., and Chao, Y. C., “Analysis of Entrainment in a Sudden Expansion Channel with Wall Mass Transfer,” Journal of Propulsion and Power, 19, pp. 514-516 (2003).CrossRefGoogle Scholar
Lee, T., “Inlet Air Temperature Effects on the Performance of the Solid Fuel Ramjet,” Journal of Thermophysics and Heat Transfer, 20, pp. 937–939 (2006).CrossRefGoogle Scholar
Tyurenkova, V., and Smirnova, M., “Material Combustion in Oxidant Flows: Self-Similar Solutions, Acta Astronautica, 120, pp. 129-137 (2016).CrossRefGoogle Scholar
Yang, J.T., Wu, C.Y.Y., and Din, S.J., “Ignition transient of a polymethylmethacrylate slab in a sudden expansion combustor,” Combustion and Flame, 98, pp. 300-308 (1994).CrossRefGoogle Scholar
Tahsini, A. M., and Farshchi, M., “Numerical Study of Solid Fuel Evaporation and Auto-Ignition in a Dump Combustor,” ACTA Astronautica, 67, pp. 774–783 (2010).CrossRefGoogle Scholar
Tahsini, A. M., and Farshchi, M., “Igniter Jet Dynamics in Solid Fuel Ramjets,” ACTA Astronautica, 64, pp. 166-175 (2009).CrossRefGoogle Scholar
Tahsini, A. M., “Piloted Ignition of Solid Fuels in Turbulent Back-Step Flows,” Aerospace Science and Technology, 18, pp. 8-14 (2012).Google Scholar
Duesterhaus, D. A., and Hogl, A., “Measurements in a Solid Fuel Ramjet Combustion with Swirl,” AIAA 24th Joint Propulsion Conference, Boston, pp. 3045–3055 (1988).Google Scholar
Campbell, W. H., Ko, B. N., Lowe, S. R., and Netzer, D. W., “Solid-Fuel Ramjet Fuel Regression Rate/Thrust Modulation,” Journal of Propulsion and Power, 8, pp. 624-629 (1992).CrossRefGoogle Scholar
Musa, O., Xiong, C., and Changsheng, Z., “Combustion Characteristics and Turbulence Modeling of Swirling Reacting Flow in Solid Fuel Ramjet,” ACTA Astronautica, 139, pp. 1-17 (2017).CrossRefGoogle Scholar
Musa, O., Xiong, C., Changsheng, Z., and Li, W., “Effect of Inlet Conditions on Swirling Turbulent Reacting Flows in a Solid Fuel Ramjet Engine,” Applied Thermal Engineering, 113, pp. 186-207 (2017).CrossRefGoogle Scholar
Musa, O., Xiong, C., Weixuan, L., and Wenhe, L., “Combustion Characteristics of a Novel Design of Solid-Fuel Ramjet Motor with Swirl Flow,” Aerospace Science and Technology, 92, pp. 750-765 (2019).CrossRefGoogle Scholar
Nusca, M. J., “Steady Flow Combustion Model for Solid Fuel Ramjet Projectiles,” Journal of Propulsion and Power, 6, pp. 348-352 (1990).CrossRefGoogle Scholar
Plett, E. G., and Stowe, R. A., “Numerical Simulation of Solid Fuel Ramjet Missile Propulsive Performance,” 31st Joint Propulsion Conference, AIAA-95-2448, CA, (1995).Google Scholar
McDonald, B., and Rice, J., “Solid Fuel Ramjet Fuel Optimization for Maximum Thrust to Drag Ratio and Impulse Density Subject to Geometric Restraints on Missile Outer Mold Line,” Aerospace Science and Technology, 75, pp. 47-57 (2018).CrossRefGoogle Scholar
McDonald, B., and Rice, J., “Solid Fuel Ramjet Fuel Optimization for Maximum Impulse-Density with Respect to Air to Fuel Ratio and Relative Fuel Regression Rates Derived from Thermogravimetric Analysis,” Aerospace Science and Technology, 86, pp. 478-486 (2019).CrossRefGoogle Scholar
Salgansky, E. A., Lutsenko, N. A., Levin, V. A., and Yanovskiy, L. S., “Modeling of Solid Fuel Gasification in Combined Charge of Low-Temperature Gas Generator for High-Speed Ramjet Engine,” Aerospace Science and Technology, 84, pp. 31-36 (2019).CrossRefGoogle Scholar
Yang, L., Yonggang, G., Zexin, C., and Dong, Z., “Mixing and Heat Release Characteristics in the Combustor of Solid-Fuel Rocket Scramjet Based on DES,” Aerospace Science and Technology, 94, (2019).Google Scholar
Spalart, P. R., and Allmaras, S. R., “A One Equation Turbulence Model for Aerodynamic Flows,” 30th Aerospace Sciences Meeting and Exhibit, AIAA-92-439, NV, (1992).Google Scholar
Liou, M. S., “A Sequel to AUSM: AUSM+,” Journal of Computational Physics, 129, pp. 364-382 (1996).Google Scholar
Tahsini, A. M., “Heat Release Effects on Drag Reduction in High Speed Flows,” International Journal of Heat and Mass Transfer, 57, pp. 657-661 (2013).Google Scholar
Tahsini, A. M., “Transient Burning of Non-Charring Materials in Boundary Layer Diffusion Flames,” Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 228, pp. 586-593 (2014).CrossRefGoogle Scholar
Tahsini, A. M., and Tadayon Mousavi, S., “Investigating the Supersonic Combustion Efficiency for the Jet-in-Cross-Flow,” International Journal of Hydrogen Energy, 40, pp. 3091-3097 (2015).CrossRefGoogle Scholar
Tahsini, A. M., “Combustion Efficiency and Pressure Loss Balance for the Supersonic Combustor,” Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 234, pp. 1149-1156 (2020).CrossRefGoogle Scholar
Yang, J. T., and Wu, C. Y. Y., “Controlling Mechanism of Ignition of Solid Fuel in a Sudden Expansion Combustor,” Journal of Propulsion and Power, 11, pp. 483-488 (1995).CrossRefGoogle Scholar
Vogel, J. C., and Eaton, J. K., “Combined Heat Transfer and Fluid Dynamics Measurements Downstream of a Backward-Facing Step,” Journal of Heat Transfer, 107, pp. 922-929 (1985).CrossRefGoogle Scholar
Chen, Y. T., Nie, J. H., Armaly, B. F., and Hsieh, H. T., “Turbulent Separated Convection Flow Adjacent to Backward-Facing Step—Effects of Step Height,” International Journal of Heat and Mass Transfer, 49, pp. 3670-3680 (2006).CrossRefGoogle Scholar
Nizou, P.Y., Tida, “Transferts de Chaleur et de Quantite de Movement dans les Jets Parietaux Plans Turbulents,” International Journal of Heat and Mass Transfer, 38, pp. 1187-1200 (1995).CrossRefGoogle Scholar