Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T08:05:05.607Z Has data issue: false hasContentIssue false
  • English
  • Français

A Simple and Accurate 3D Numerical Model for Laser Cladding

Published online by Cambridge University Press:  04 November 2019

Shih-Kai Chien ,
Kuo-Teng Tsai ,
Yueh-Heng Li ,
Yu-Ting Wu  and
Wen-Lih Chen
Shih-Kai Chien
Affiliation:
Laser and Additive Manufacturing Technology CenterIndustrial Technology Research InstituteTainan, Taiwan
Kuo-Teng Tsai
Affiliation:
Laser and Additive Manufacturing Technology CenterIndustrial Technology Research InstituteTainan, Taiwan
Yueh-Heng Li
Affiliation:
Department of Aeronautics and AstronauticsNational Cheng Kung UniversityTainan, Taiwan
Yu-Ting Wu
Affiliation:
Department of Engineering ScienceNational Cheng Kung UniversityTainan, Taiwan
Wen-Lih Chen*
Affiliation:
Department of Aeronautics and AstronauticsNational Cheng Kung UniversityTainan, Taiwan
*
*Corresponding author ([email protected])
Get access

Abstract

A simple numerical model has been proposed for laser cladding. The model does not involve complex techniques such as cell addition, moving mesh, or prescribing a clad profile with a certain polynomial function. Instead, a mass function has been introduced to register the clad mass deposition on substrate, and from which the clad-track height can be estimated. The model takes several operational parameters, laser power, laser-head speed, and clad powder feeding rate, into consideration and predicts clad-track geometry, dilution, and substrate temperature. Experiments using two different combinations of substrate and clad powder materials to lay single and multiple clad tracks were conducted to provide data for model validation. The results show that the present model returns good agreement with experimental clad profiles for single and multiple tracks.

Keywords

laser claddingnumerical methodclad profiledilution
Type
Research Article
Information
Journal of Mechanics , Volume 36 , Issue 1 , February 2020 , pp. 19 - 33
Copyright
Copyright © 2019 The Society of Theoretical and Applied Mechanics 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Q., Nguyen, C.Y., Yang, “Inverse determination of laser power on laser welding with a given width penetration by a modified Newton-Raphson method,” International Communications in Heat and Mass Transfer, 65, pp. 15–21 (2015).CrossRefGoogle Scholar
V., Pavelic, R., Tanbakuchi, O.A., Uyehara, “Experimental and computed temperature histories in gas tungsten arc welding of thin plates,” Welding Journal Research Supplement, 48, pp. 295–305 (1969).Google Scholar
J., Goldak, A., Chakravarti, M., Bibby, “A new finite element model for welding heat sources,” Metallurgical and Material Transactions B, 15B, pp. 299–305 (1984).CrossRefGoogle Scholar
J., Goldak, “Computer modeling of heat flow in welds” Metallurgical and Material Transactions B, 17, pp. 587–600 (1986).CrossRefGoogle Scholar
E.J., Ha, W.S., Kim, “A study of low-power density laser welding process with evolution of free surface,” International Journal of Heat Fluid Flows, 26 (4), pp. 613–521 (2005).CrossRefGoogle Scholar
A., De, B., DebRoy, “Probing unknown welding parameters from convective heat transfer calculation and multivariable optimization,” Journal of Physics B, 37 (1), pp. 140–150 (2004).CrossRefGoogle Scholar
C., Lalas, K., Tsirbas, K., Salonitis, G., Chryssolouris, “An analytical model of the laser clad geometry,” International Journal of Advanced Manufacturing Technology, 32, pp. 34–41 (2007).CrossRefGoogle Scholar
E., Toyserkani, A., Khajepour, S., Corbin, “3-D finite element modeling of laser cladding by powder injection: effects of laser pulse shaping on the process,” Optics and Lasers in Engineering, 41, pp. 849–867 (2004).CrossRefGoogle Scholar
W., Ya, B., Pathiraj, S., Liu, “2D modeling of clad geometry and resulting thermal cycle during laser cladding,” Journal of Materials Processing Technology, 230, pp. 217–232 (2016).CrossRefGoogle Scholar
J.T., Hofman, D.E., de Lange, B., Pathiraj, J., Meijer, “FEM modelling and experimental verification for dilution control in laser cladding,” Journal of Materials Processing Technology, 211, pp. 187–196 (2011).CrossRefGoogle Scholar
G., Palumbo, S., Pinto, L., Tricarico, “Numerical finite element investigation on laser cladding treatment of ring geometries,” Journal of Materials Processing Technology, 155-156, pp. 1443–1450 (2004).CrossRefGoogle Scholar
R., Parekh, R.K., Buddu, R.I., Patel, “Multiphysics simulation of laser cladding process to study the effect of process parameters on clad geometry,” Procedia Technology, 23, pp. 529–536 (2016).CrossRefGoogle Scholar
J., Liu, L., Li, “Study on cross-section clad profile in coaxial single-pass cladding with a low-power laser,” Optics & Laser Technology, 37, pp. 478–482 (2005).CrossRefGoogle Scholar
M., Sistaninia, M., Sistaninia, H., Moeanodini, “Laser surface hardening considering coupled thermoelasticity,” Journal of Mechanics, 25, pp. 241249 (2009).CrossRefGoogle Scholar
L.X., Yang, X.F., Peng, B.X., Wang, “Numerical modeling and experimental investigation on the characteristics of molten pool during laser processing,” International Journal of Heat and Mass Transfer, 44, pp. 4465–4473 (1986).CrossRefGoogle Scholar
F.S., Lien, W.L., Chen, M.A., Leschziner, “A multiblock implementation of a non-orthogonal, collocated finite volume algorithm for complex turbulent flows,” International Journal of Numerical Methods in Fluids, 23, pp. 567–588 (1996).3.0.CO;2-A>CrossRefGoogle Scholar
K.C., Mills, “Recommended values of thermal physical properties for selected commercial alloys,” Woodhead Publishing Ltd., Cambridge, UK (2002).CrossRefGoogle Scholar
J.T., Hofman, “Development of an observation and control system for industrial laser cladding,” Ph.D. Thesis, University of Twente, The Netherlands (2009).Google Scholar