Hostname: page-component-745bb68f8f-l4dxg Total loading time: 0 Render date: 2025-01-09T19:40:32.599Z Has data issue: false hasContentIssue false
  • English
  • Français

Strength enhancement of single crystal laser components

Published online by Cambridge University Press:  31 January 2011

K.E. Shafer ,
D.E. Eakins ,
D.F. Bahr ,
M.G. Norton  and
K.G. Lynn
K.E. Shafer
Affiliation:
Center for Materials Research, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
D.E. Eakins
Affiliation:
Center for Materials Research, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
D.F. Bahr*
Affiliation:
Center for Materials Research, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
M.G. Norton
Affiliation:
Center for Materials Research, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
K.G. Lynn
Affiliation:
Center for Materials Research, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The effect of chemical etching on the surface roughness and fracture strength of Nd:yttrium-aluminum-garnet single crystals was investigated. Etching the laser host material in a 1:1 mixture of concentrated sulfuric and phosphoric acid at elevated temperatures enabled material removal from the surface of laser rods cored from single-crystal boules. The roughness on the rod surface increased from the as-drilled condition after etching, but after 17 μm of material was removed, the roughness remained approximately constant. The modulus of rupture increased from 133-530 MPa when 87 μm of material was removed by the chemical etching procedure.

Type
Rapid Communications
Information
Journal of Materials Research , Volume 18 , Issue 11 , November 2003 , pp. 2537 - 2539
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Xiao, Q. and Derby, J.. J. Crystal Growth 139, 147 (1994).CrossRefGoogle Scholar
2.Vatnik, S.M., El-Agmy, R, and Graf, T., J. Mod. Optics 49, 2059 (2002).CrossRefGoogle Scholar
3.Clarkson, W.A., J. Phys. D: Appl. Phys. 34, 2381 (2001).CrossRefGoogle Scholar
4.Xie, W., Tam, S., Lam, Y., Yang, H., Liu, J., Gu, J., and Tan, W., Optics Laser Technol. 32, 193 (2003).CrossRefGoogle Scholar
5.Koechner, W., Solid State Laser Engineering, 5th ed. (Springer, Berlin, 1999), pp. 48, 406-413.CrossRefGoogle Scholar
6.Mah, T. and Parthasarathy, T.A., Scripta Metall. Mater. 28, 1383 (1993).CrossRefGoogle Scholar
7.Blumenthal, W.R. and Taylor, S.T., Acta Mater. 45, 3071 (1997).Google Scholar
8.ASTM. ASTM Standard Test Methods for Strength of Glass by Flexure, Determination of Modulus of Rupture, Designation C 158 - 95 (ASTM, West Conshohocken, NJ, 1995).Google Scholar
9.Gerber, M. and Graf, Th., Optics Laser Technol. 33, 449 (2001).CrossRefGoogle Scholar
10.Koechner, W., Appl. Phys. 2, 279 (1973).CrossRefGoogle Scholar
11.Vogel, F.L., Pfann, W.G., Corey, H.E., and Thomas, E.E., Phys. Rev. 90, 489 (1953).Google Scholar
12.Zlatkin, A.T. and Lube, E.L., J. Crystal Growth 118, 218 (1992).Google Scholar
13.Marion, J., Appl. Phys. Lett. 47, 694 (1985).CrossRefGoogle Scholar