Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-23T16:31:11.144Z Has data issue: false hasContentIssue false
  • English
  • Français

Shaping of ceramic parts by selective laser melting of powder bed

Published online by Cambridge University Press:  07 July 2014

Enrique Juste ,
Fabrice Petit ,
Véronique Lardot  and
Francis Cambier
Enrique Juste*
Affiliation:
Belgian Ceramic Research Center – Member of EMRA, Mons 7000, Belgium
Fabrice Petit
Affiliation:
Belgian Ceramic Research Center – Member of EMRA, Mons 7000, Belgium
Véronique Lardot
Affiliation:
Belgian Ceramic Research Center – Member of EMRA, Mons 7000, Belgium
Francis Cambier
Affiliation:
Belgian Ceramic Research Center – Member of EMRA, Mons 7000, Belgium
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Laser additive manufacturing allows the production of polymeric or metallic parts with complex shapes. A major advantage of this contactless technology is that it allows reaching very high energy densities with an excellent precision in short times. This is very suitable for processing hard refractory metals for instance. Unfortunately, current results are less satisfactory for ceramics as a consequence of their intrinsic properties such as a low thermal shock resistance and very high refractoriness. Another significant limitation is related to the poor absorptivity of oxide ceramics in the near-infrared region which is typical for most commercial selective laser melting (SLM) machines. This study considers an alternative to overcome the above-mentioned limitations, especially the lack of absorptivity. SLM of oxide ceramics has become possible. Large parts with complex shapes and relative densities up to 90% have been manufactured on a commercial SLM machine.

Keywords

ceramiclasersintering
Type
Invited Papers
Information
Journal of Materials Research , Volume 29 , Issue 17: Focus Issue: The Materials Science of Additive Manufacturing , 14 September 2014 , pp. 2086 - 2094
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Bourell, D.L., Marcus, H.L., Barlow, J.W., and Beaman, J.J.: Laser sintering of metals and ceramics. Int. J. Powder Metall. 28(4), 369 (1992).Google Scholar
Kruth, J-P., Levy, G., Klocke, F., and Childs, T.H.C.: Consolidation phenomena in laser and powder-bed based layered manufacturing. Ann. CIRP 56(2), 730 (2007).Google Scholar
Pawlowski, L.: Thick laser coatings: A review. J. Therm. Spray Technol. 8(2), 279 (1999).Google Scholar
Kniter, R. and Bauer, W.: Ceramic microfabrication by rapid prototyping process chains. Sadhana 28, 307 (2003).Google Scholar
Wilkes, J. and Wissenbach, K.: Rapid manufacturing of ceramic components for medical and technical applications via selective laser melting. In Euro-uRapid, Frankfurt, Vol. A4-1 (2006).Google Scholar
Lenk, R., Nagy, A., Richter, H-J., and Techel, A.: Material development for laser sintering of silicon carbide. Cfi/Ber. DKG 83, 41 (2006).Google Scholar
Yang, Y., Bai, X., Xie, Z., Kuang, T., Liu, Z., Zhuang, Y., Tong, B., and Liang, Y.: Influence of additive silica on the laser melting of the ceramic coatings. J. Mater. Sci. Technol. 19, 33 (2003).Google Scholar
Matthiesen, D.H. and Petuskey, W.T.: Solidification microstructures of laser-melted alumina powder compacts. J. Am. Ceram. Soc. 68, 114 (1985).Google Scholar
Wu, Y., Du, J., Choy, K-L., and Hench, L.L.: Laser densification of alumina powder beds generated using aerosol assisted spray deposition. J. Eur. Ceram. Soc. 27, 4727 (2007).CrossRefGoogle Scholar
Jasim, K.M., Rawlings, R.D., and West, D.R.F.: Operating regimes for laser surface engineering of ceramics. J. Mater. Sci. 27, 1937 (1992).Google Scholar
Tian, X., Günster, J., Melcher, J., Li, D., and Heinrich, J.G.: Process parameters analysis of direct laser sintering and post treatment of porcelain components using Taguchi's method. J. Eur. Ceram. Soc. 29, 1903 (2009).Google Scholar
Hellrung, D., Yeh, L-Y., Depiereux, F., Gillner, A., and Poprawe, R.: High-accuracy micromachining of ceramics by frequency-tripled Nd:YAG-lasers. In Proc. of the SPIE Conference on Laser Applications in Microelectronic and Optoelectronic Manufacturing IV, Vol. 3618, 348 (1999).Google Scholar
Pham, D.T., Dimov, S.S., and Petkov, P.V.: Laser milling of ceramic component. Int. J. Mach. Tools Manuf. 47, 618 (2007).Google Scholar
Shao, T.M., Lin, X.C., and Zhou, M.: Absorption of some powder materials to YAG laser. Sci. China, Ser. A 44(S1), 489 (2001).Google Scholar
Deckers, J., Shazad, K., Vleuels, J., and Kruth, J.P.: Isostatic pressing assisted indirect selective laser sintering of alumina components. Rapid Prototyping J. 18, 409 (2012).Google Scholar
Tolochko, N.K., Laoui, T., Khlopkov, Y.V., Mozzharov, S.E., Titov, V.I., and Ignatiev, M.B.: Absorbance of powder materials suitable for laser sintering. Rapid Prototyping J. 6, 155 (2000).Google Scholar
Su, X. and Yang, Y.: Research on track overlapping during selective laser melting of powders. J. Mater. Process Technol. 212, 2074 (2012).Google Scholar
Tian, X., Mühler, T., Gomez, C., Günster, J., and Heinrich, J.G.: Feasibility study on rapid prototyping of porcelain products. J. Ceram. Sci. Technol. 02, 217 (2011).Google Scholar
Bertrand, Ph., Bayle, F., Combe, C., Goeuriot, P., and Smurov, I.: Ceramic components manufacturing by selective laser sintering. Appl. Surf. Sci. 254, 989 (2007).Google Scholar