Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-11-26T08:09:43.201Z Has data issue: false hasContentIssue false
  • English
  • Français

Relation between the ratio of elastic work to the total work of indentation and the ratio of hardness to Young's modulus for a perfect conical tip

Published online by Cambridge University Press:  31 January 2011

J. Chen  and
S.J. Bull
J. Chen
Affiliation:
School of Chemical Engineering and Advanced Materials, Newcastle University, Merz Court, Newcastle upon Tyne, NE1 7RU, United Kingdom
S.J. Bull*
Affiliation:
School of Chemical Engineering and Advanced Materials, Newcastle University, Merz Court, Newcastle upon Tyne, NE1 7RU, United Kingdom
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

A linear relationship between the ratio of elastic work to the total indentation work and hardness to reduced modulus, i.e., We/Wt = λ H/Er, has been derived analytically and numerically in a number of studies and has been widely accepted. However, the scaling relationship between We/Wt and H/Er has recently been questioned, and it was found that λ is actually not a constant but is related to material properties. In this study, a new relationship between We/Wt and H/Er has been derived, which shows excellent agreement with numerical simulation and experimental results. We also propose a method for obtaining the elastic modulus and hardness of a material without invoking the commonly used Oliver and Pharr method. Furthermore, it is demonstrated that this method is less sensitive to tip imperfections than the Oliver and Pharr approach is.

Keywords

Elastic propertiesHardnessNanoindentation
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 590 - 598
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Stilwell, N.A. and Tabor, D.: Elastic recovery of conical indentations. Proc. Phys. Soc. London 78, 169 (1961).CrossRefGoogle Scholar
2.Cheng, Y-T., Li, Z., and Cheng, C-M.: Scaling relationships for indentation measurements. Philos. Mag. A 82, 1821 (2002).CrossRefGoogle Scholar
3.Cheng, Y-T. and Cheng, C-M.: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 (1998).CrossRefGoogle Scholar
4.Giannakopoulos, A.E. and Suresh, S.: Determination of elastoplastic properties by instrumented sharp indentation. Scr. Mater. 40, 1191 (1999).CrossRefGoogle Scholar
5.Ma, D., Chung, W., Liu, J., and He, J.: Determination of Young's modulus by nanoindentation. Sci. China, Ser. E 47, 398 (2004).CrossRefGoogle Scholar
6.Malzbender, J.: Comment on the determination of mechanical properties from the energy dissipated during indentation. J. Mater. Res. 20, 1090 (2005).CrossRefGoogle Scholar
7.Oliver, W.C.: Alternative technique for analyzing instrumented indentation data. J. Mater. Res. 16, 3202 (2001).CrossRefGoogle Scholar
8.Hainsworth, S.V., Chandler, H.W., and Page, T.F.: Analysis of nanoindentation load-displacement loading curves. J. Mater. Res. 11, 1987 (1996).CrossRefGoogle Scholar
9.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
10.Pharr, G.M. and Bolshakov, A.: Understanding nanoindentation unloading curves. J. Mater. Res. 17, 2660 (2002).CrossRefGoogle Scholar
11.Cheng, Y-T. and Cheng, C-M.: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng., R 44, 91 (2004).CrossRefGoogle Scholar
12.Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
13.Hay, J.C., Bolshakov, A., and Pharr, G.M.: A critical examination of the fundamental relations used in the analysis of nanoindentation. J. Mater. Res. 14, 2296 (1999).CrossRefGoogle Scholar
14.Alkorta, J., Martínez-Esnaola, J.M., and Gil Sevillano, J.: Comments on “Comment on the determination of mechanical properties from the energy dissipated during indentation” by J. Malzbender [J. Mater. Res. 20, 1090 (2005)]. J. Mater. Res. 21, 302 (2006).Google Scholar
15.Choi, Y., Lee, H.S., and Kwon, D.: Analysis of sharp-tip-indentation load-displacement curve for contact area determination taking into account pile-up and sink-in effects. J. Mater. Res. 19, 3307 (2004).CrossRefGoogle Scholar
16.Sakai, M.: Simultaneous estimate of elastic/plastic parameters in depth-sensing indentation tests. Scr. Mater. 51, 391 (2004).CrossRefGoogle Scholar
17.Marx, V. and Balke, H.: A critical investigation of the unloading behavior of sharp indentation. Acta Mater. 45, 3791 (1997).CrossRefGoogle Scholar
18.Malzbender, J. and de, G. With: Indentation load-displacement curve, plastic deformation and energy. J. Mater. Res. 17, 502 (2002).CrossRefGoogle Scholar
19.Chen, J. and Bull, S.J.: A critical examination of the relationship between plastic deformation zone size and Young's modulus to hardness ratio in indentation testing. J. Mater. Res. 21, 2617 (2006).CrossRefGoogle Scholar
20.Li, M., Chen, W., Liang, N., and Wang, L.: A numerical study of indentation using indenters of different geometry. J. Mater. Res. 19, 73 (2004).Google Scholar
21.Soare, S.: Design of a rotating sensor for stress measurement in metallization. Ph.D. Thesis, University of Newcastle upon Tyne, UK, 2004.Google Scholar
22.Jayaraman, S., Hahn, G.T., Oliver, W.C., Rubin, C.A., and Bastias, P.C.: Determination of monotonic stress-strain curve of hard materials from ultra-low-load indentation tests. Int. J. Solids Struct. 35, 365 (1998).CrossRefGoogle Scholar
23.Venkatesh, T.A., Van Vleit, K.J., Ginnakopoulos, A.E., and Suresh, S.: Determination of elasto-plastic properties by instrumented sharp indentation: Guidelines for property extraction. Scr. Mater. 42, 833 (2000).CrossRefGoogle Scholar
24.Palacio, J.F.: Mechanical properties of high performance fuller-ene-like CNx coatings assessed by nanoindentation. Ph.D. Thesis, University of Newcastle upon Tyne, UK, 2006.Google Scholar
25.Cheng, Y.T. and Cheng, C.M.: Further analysis of indentation loading curves: Effects of tip rounding on mechanical property measurements. J. Mater. Res. 13, 1059 (1998).CrossRefGoogle Scholar
26.Chen, J. and Bull, S.J.: On the relationship between plastic zone radius and maximum depth during nanoindentation. Surf. Coat. Technol. 201, 4289 (2006).CrossRefGoogle Scholar
27.Bei, H., George, E.P., Hay, J.L., and Pharr, G.M.: Influence of indenter tip geometry on elastic deformation during nanoindentation. Phys. Rev. Lett. 95(045501), 1 (2005).CrossRefGoogle ScholarPubMed
28.Chen, J. and Bull, S.J.: Multicycling nanoindentation study on thin optical coatings on glass. J. Phys. D: Appl. Phys. 41, 074009 (2008).CrossRefGoogle Scholar