Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-26T22:41:52.886Z Has data issue: false hasContentIssue false

Production of Al–Ti–C grain refiner alloys by reactive synthesis of elemental powders: Part I. Reactive synthesis and characterization of alloys

Published online by Cambridge University Press:  31 January 2011

H. J. Brinkman
Affiliation:
Laboratory of Materials Science, Delft University of Technology, Rotterdamseweg 137,2628 AL Delft, The Netherlands
F. Zupanič
Affiliation:
Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, SI-2000 Maribor, Slovenia
J. Duszczyk
Affiliation:
Laboratory of Materials Science, Delft University of Technology, Rotterdamseweg 137,2628 AL Delft, The Netherlands
L. Katgerman
Affiliation:
Laboratory of Materials Science, Delft University of Technology, Rotterdamseweg 137,2628 AL Delft, The Netherlands
Get access

Abstract

The first part of this article reports on the reactive synthesis and characterization of Al–Ti–C alloys intended as master alloys for aluminum grain refining. The alloys were produced from elemental powders by the thermal explosion mode and analyzed with x-ray diffraction, scanning electron microscopy, and differential scanning calorimetry. Parameters were the titanium concentration (15 and 30 wt%) and the Ti/C ratio (9/1, 20/1, and 120/1) in the reactant powder mixture and the cooling rate after the reactive synthesis (1 and 120 °C/min). Full conversion of titanium and carbon into Al3Ti and TiC was achieved for the 30 wt% Ti mixtures but not for the 15 wt% Ti mixtures where the reaction was not exothermic enough. The Ti/C ratio did not affect the phase composition after reactive synthesis in the 30 wt% Ti alloys and could be used to tailor the microstructure of the alloy. The formation of Al4C3 was suppressed with a high cooling rate after the exothermic formation reactions.

Type
Articles
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.McCartney, D.G., Int. Mater. Rev. 34, 247 (1989).CrossRefGoogle Scholar
2.Hoefs, P., Reif, W., Green, A.H., van Wiggen, P.C., Schneider, W., and Brandner, D., in Light Metals 1997, edited by Huglen, R. (Proceedings of the TMS annual meeting, Warrendale, PA, 1997), p. 777784.Google Scholar
3.Hadia, M.A., Ghaneya, A.A., and Niazi, A., in Light Metals 1996, edited by Hale, W. (Proceedings of the TMS annual meeting, Warrendale, PA, 1996), pp. 729736.Google Scholar
4.Banerji, A., Reif, W., and Feng, Q., J. Mater. Sci. 29, 1958 (1994).CrossRefGoogle Scholar
5.Whitehead, A.J., Danilak, S.A., and Granger, D.A., in Light Metals 1997, edited by Huglen, R. (Proceedings of the TMS annual meeting, Warrendale, PA, 1997), pp. 785793.Google Scholar
6.Merzhanov, A.G., Int. J. SHS, 6(2), 119 (1997).Google Scholar
7.Hardman, A. and Hayes, F.H., Mater. Sci. Forum 217–222, 247 (1996).CrossRefGoogle Scholar
8.Sato, K. and Fleming, M.C., Met. Mater. Trans. A 29A, 1707 (1998).CrossRefGoogle Scholar
9.Easton, M. and John, D. St., Met. Mater. Trans. A 30A, 1613 (1999).CrossRefGoogle Scholar
10.Lee, W.C. and Chung, S.L., J. Am. Ceram. Soc. 80(1), 53 (1997).CrossRefGoogle Scholar
11.Choi, Y. and Rhea, S.W., J. Mater. Sci. 28, 6669 (1993).CrossRefGoogle Scholar
12.Choi, Y., Mullins, M.E., Wijayatilleke, K., and Lee, J.K., Met. Trans. A 23A, 2387 (1992).CrossRefGoogle Scholar
13.Frage, N., Frumin, N., Levin, L., Polack, M., and Daniel, M.P., Met. Mater. Trans. A 29A, 13411345 (1998).CrossRefGoogle Scholar
14.Svensson, L. and Jarfors, A., Mater. Sci. Technol. 9, 948 (1993).Google Scholar
15.Mackowiak, J. and Shreir, L.L., J. Less-Common Met. 1, 456 (1959).CrossRefGoogle Scholar
16.Böhm, A., Jüngling, T., and Kieback, B., in Advances in Powder Metallurgy & Particulate Materials, edited by Cradle, T.M. and Narasimham, K.S. (Proceedings of the APMI Powder Metallurgical Conference, Princeton, NJ, 1996), Vol. 10, pp. 5158.Google Scholar