Crossref Citations
This article has been cited by the following publications. This list is generated based on data provided by
Crossref.
Shim, Sanghoon
Oliver, Warren C.
and
Pharr, George M.
2004.
A critical examination of the Berkovich vs. conical indentation based on 3D finite element calculation.
MRS Proceedings,
Vol. 841,
Issue. ,
Leggoe, J.W.
2004.
Determination of the elastic modulus of microscale ceramic particles via nanoindentation.
Journal of Materials Research,
Vol. 19,
Issue. 8,
p.
2437.
Ganneau, F.P.
Constantinides, G.
and
Ulm, F.-J.
2006.
Dual-indentation technique for the assessment of strength properties of cohesive-frictional materials.
International Journal of Solids and Structures,
Vol. 43,
Issue. 6,
p.
1727.
Chen, J.
and
Bull, S.J.
2006.
On the relationship between plastic zone radius and maximum depth during nanoindentation.
Surface and Coatings Technology,
Vol. 201,
Issue. 7,
p.
4289.
Swaddiwudhipong, S
Hua, J
Tho, K K
and
Liu, Z S
2006.
Equivalency of Berkovich and conical load-indentation curves.
Modelling and Simulation in Materials Science and Engineering,
Vol. 14,
Issue. 1,
p.
71.
Chen, J.
and
Bull, S.J.
2006.
A critical examination of the relationship between plastic deformation zone size and Young's modulus to hardness ratio in indentation testing.
Journal of Materials Research,
Vol. 21,
Issue. 10,
p.
2617.
Tranchida, Davide
Piccarolo, Stefano
and
Soliman, Maria
2006.
Nanoscale Mechanical Characterization of Polymers by AFM Nanoindentations: Critical Approach to the Elastic Characterization.
Macromolecules,
Vol. 39,
Issue. 13,
p.
4547.
Wang, Tong Hong
Fang, Te-Hua
and
Lin, Yu-Cheng
2007.
A numerical study of factors affecting the characterization of nanoindentation on silicon.
Materials Science and Engineering: A,
Vol. 447,
Issue. 1-2,
p.
244.
Golovin, Yu. I.
2008.
Nanoindentation and mechanical properties of solids in submicrovolumes, thin near-surface layers, and films: A Review.
Physics of the Solid State,
Vol. 50,
Issue. 12,
p.
2205.
Chen, J.
and
Bull, S. J.
2008.
Investigation of the relationship between work done during indentation and the hardness and Young's modulus obtained by indentation testing.
International Journal of Materials Research,
Vol. 99,
Issue. 8,
p.
852.
Bolelli, Giovanni
Cannillo, Valeria
Lusvarghi, Luca
Mantini, Fabio Pighetti
Gualtieri, Enrico
and
Menozzi, Claudia
2008.
An FIB study of sharp indentation testing on plasma-sprayed TiO2.
Materials Letters,
Vol. 62,
Issue. 10-11,
p.
1557.
Qin, J.
Huang, Y.
Xiao, J.
and
Hwang, K.C.
2009.
The equivalence of axisymmetric indentation model for three-dimensional indentation hardness.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
776.
Bhattacharyya, D.
Mara, N.A.
Dickerson, P.
Hoagland, R.G.
and
Misra, A.
2009.
Transmission electron microscopy study of the deformation behavior of Cu/Nb and Cu/Ni nanoscale multilayers during nanoindentation.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
1291.
Sakharova, N.A.
Fernandes, J.V.
Antunes, J.M.
and
Oliveira, M.C.
2009.
Comparison between Berkovich, Vickers and conical indentation tests: A three-dimensional numerical simulation study.
International Journal of Solids and Structures,
Vol. 46,
Issue. 5,
p.
1095.
Chen, J.
and
Bull, S.J.
2009.
Relation between the ratio of elastic work to the total work of indentation and the ratio of hardness to Young's modulus for a perfect conical tip.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
590.
Aida Rodríguez Pulecio, Sara
Cristina Moré Farias, María
and
Souza, Roberto Martins
2009.
Analysis of the tip roundness effects on the micro- and macroindentation response of elastic–plastic materials.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
1037.
Chen, J.
and
Bull, S.J.
2009.
On the factors affecting the critical indenter penetration for measurement of coating hardness.
Vacuum,
Vol. 83,
Issue. 6,
p.
911.
Deuschle, Julia K.
Matthias Deuschle, H.
Enders, Susan
and
Arzt, Eduard
2009.
Contact area determination in indentation testing of elastomers.
Journal of Materials Research,
Vol. 24,
Issue. 3,
p.
736.
Moore, Steven W.
Manzari, Majid T.
and
Shen, Yin-Lin
2010.
Nanoindentation in elastoplastic materials: insights from numerical simulations.
International Journal of Smart and Nano Materials,
Vol. 1,
Issue. 2,
p.
95.
Chen, Wei-Min
Cheng, Yang-Tse
and
Li, Min
2010.
Indentation of power law creep solids by self-similar indenters.
Materials Science and Engineering: A,
Vol. 527,
Issue. 21-22,
p.
5613.