Hostname: page-component-cd9895bd7-8ctnn Total loading time: 0 Render date: 2024-12-24T16:56:25.108Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure and mechanical properties of Mo2Ni3Si–Al2O3 nanocomposite synthesized by mechanical alloying

Published online by Cambridge University Press:  11 October 2016

H. Chen
H. Chen*
Affiliation:
College of Materials Science and Engineering, Liaocheng University Research Institute of Non-ferrous Metal, Liaocheng University, Liaocheng 252000, China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Mo2Ni3Si–Al2O3 nanocomposite was synthesized using MoO3, Ni, Si, and Al as starting materials by mechanical alloying. The mechanically alloyed powders were consolidated by hot pressing. The morphology and structural evolution of composite powders were investigated by scanning electron microscopy (SEM) and x-ray diffraction (XRD). The microstructure and mechanical properties of the consolidated products were studied in detail. The results showed that Mo2Ni3Si–Al2O3 composite was obtained after 10 h of milling. The reaction mechanism mechanically induced self propagating reaction. The mean grain size of Mo2Ni3Si and Al2O3 after milling for 20 h were 15.9 and 32.4 nm, respectively. The Mo2Ni3Si–Al2O3 composite powders are stable during an annealing at 1000 °C. After consolidation, Mo2Ni3Si–Al2O3 composite has a high density (96.3%) and fine-grain (microns and submicrometer range). The hardness, flexure strength, and fracture toughness of Mo2Ni3Si–Al2O3 composite are 13 GPa, 533 MPa, and 6.29 MPa·m1/2, respectively. Meanwhile, the composite has higher strength at high temperature, and the strength remains stable up to 1000 °C (about 513 MPa).

Keywords

microstructurecompositemechanical alloying
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 21 , 14 November 2016 , pp. 3352 - 3359
Check for updates
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Gnesin, B.A., Gnesin, I.B., and Nekrasov, A.N.: The interaction of carbon with Mo5Si3 and W5Si3 silicides Nowotny phase synthesis. Intermetallics 41, 82 (2013).Google Scholar
Chen, H., Shao, X., Wang, C.Z., Pu, X.P., Ma, J., and Huang, B.X.: Effect of Al2O3 and Cu on the microstructure and oxidation properties of Mo5Si3 composite. Corros. Sci. 94, 129 (2015).CrossRefGoogle Scholar
Xu, J., Hu, W., Yan, Y., Lu, X.L., Munroe, P., and Xie, Z.H.: Microstructure and mechanical properties of a Mo-toughened Mo3Si-based in situ nanocomposite. Vacuum 109, 112 (2014).Google Scholar
Zamani, S., Bakhsheshi-Rad, H.R., Shokuhfar, A., Vaezi, M.R., Kadir, M.R., and Shafiee, M.R.: Synthesis and characterization of MoSi2–Mo5Si3 nanocomposite by mechanical alloying and heat treatment. Int. J. Refract. Met. Hard Mater. 31, 236 (2012).Google Scholar
Seong-Ho, H., Kyosuke, Y., Kouichi, M., Rong, T., and Takashi, G.: Compositional regions of single phases at 1800 °C in Mo-rich Mo–Si–B ternary system. Mater. Sci. Eng., A 552, 179 (2012).Google Scholar
Lu, X.D. and Wang, H.M.: Microstructure and dry sliding wear properties of laser clad Mo2Ni3Si/NiSi metal silicide composite coatings. J. Alloys Compd. 359, 287 (2003).Google Scholar
Lu, X.D. and Wang, H.M.: Dry sliding wear behavior of laser clad Mo2Ni3Si/NiSi metal silicide composite coatings. Thin Solid Films 472, 297 (2005).Google Scholar
Xu, Y.W. and Wang, H.M.: Room-temperature dry sliding wear behavior of γ-Ni/Mo2Ni3Si metal silicide “in situ” composites. J. Alloys Compd. 440, 101 (2007).CrossRefGoogle Scholar
Gui, Y., Song, C., Wang, S., and Zhao, D.: Elevated-temperature wear behaviors of NiMo/Mo2Ni3Si intermetallic “in situ” composites. J. Mater. Res. 31, 66 (2015).Google Scholar
Yongliang, G., Chunyan, S., Li, Y., and Xiaoling, Q.: Microstructure and tribological properties of NiMo/Mo2Ni3Si intermetallic “in situ” composites. J. Alloys Compd. 509, 4987 (2011).Google Scholar
Zhou, C.T., Xiao, B., Feng, J., Chen, J.C., Zhou, R., Xing, J.D., and Li, Y.F.: The stability and elastic constants of X2Ni3Si (X = Ti, Mo and W): The novel ternary metal silicides. Phys. B 404, 1701 (2009).Google Scholar
Gui, Y.L. and Wang, H.M.: Microstructure and dry sliding wear resistance of Moss-toughened Mo2Ni3Si metal silicide alloys. Int. J. Refract. Met. Hard Mater. 25, 433 (2007).Google Scholar
Kubisztal, J. and Budniok, A.: Electrolytical production of Ni + Mo + Si composite coatings with enhanced content of Si. Appl. Surf. Sci. 252, 8605 (2006).Google Scholar
Lu, X.D., Wang, H.M., and Zhou, Z.R.: Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings. Appl. Surf. Sci. 240, 432 (2005).Google Scholar
Ignacio, G., Maria, A.M., and David, G.M.: The effect of heat treatments on the microstructural stability of the intermetallic Ti–46.5Al–2W–0.5Si. Intermetallics 9, 373 (2001).Google Scholar
Manukyan, K.V., Kharatyan, S.L., Blugan, G., Kocher, P., and Kuebler, J.: MoSi2–Si3N4 composites: Influence of starting materials and fabrication route on electrical and mechanical properties. J. Eur. Ceram. Soc. 29, 2053 (2009).Google Scholar
Patel, M., Subramanyuam, J., and Bhanu Prasad, V.V.: Synthesis and mechanical properties of nanocrystalline MoSi2–SiC composite. Scr. Mater. 58, 211 (2008).Google Scholar
Zakeri, M. and Ahmadi, M.: Mechanochemical synthesis of MoSi2–SiC nanocomposite powder. Ceram. Int. 38, 2977 (2012).Google Scholar
Hu, Q.D., Luo, P., and Yan, Y.W.: Microstructures and densification of MoSi2–SiC composite by field-activated and pressure-assisted combustion synthesis. J. Alloys Compd. 468, 136 (2009).Google Scholar
Ramezanalizadeh, H. and Heshmati-Manesh, S.: Preparation of MoSi2–Al2O3 nano-composite via MASHS route. Int. J. Refract. Met. Hard Mater. 31, 210 (2012).Google Scholar
Zakeri, M., Yazdani-Rad, R., Enayati, M.H., and Rahimipoor, M.R.: Synthesis of MoSi2–Al2O3 nanocomposite by mechanical alloying. Mater. Sci. Eng., A 430, 185 (2006).Google Scholar
Chen, H., Ma, Q., Shao, X., Ma, J., Wang, C., and Huang, B.: Microstructure, mechanical properties and oxidation resistance of Mo5Si3–Al2O3 nano-composite. Mater. Sci. Eng., A 592, 12 (2014).CrossRefGoogle Scholar
Krakhmalev, P.V.: Preparation of Mo(Si, Al)2–ZrO2 nanocomposite powders by mechanical alloying. Int. J. Refract. Met. Hard Mater. 22, 205 (2004).Google Scholar
Zamani, S., BakhsheshiRad, H.R., Kadir, M.R.A., and Shafiee, M.R.M.: Synthesis and kinetic study of (Mo,W)Si2–WSi2 nanocomposite by mechanical alloying. J. Alloys Compd. 540, 248 (2012).Google Scholar
Zakeri, M., Yazdani-Rad, R., Enayati, M.H., Rahimipour, M.R., and Mobasherpour, I.: Mechanochemical reduction of MoO3/SiO2 powder mixtures by Al and carbon for the synthesis of nanocrystalline MoSi2 . J. Alloys Compd. 430, 170 (2007).Google Scholar
Mousavi, T., Karimzadeh, F., and Abbasi, M.H.: Synthesis and characterization of nanocrystalline NiTi intermetallic by mechanical alloying. Mater. Sci. Eng., A 487, 46 (2008).Google Scholar
Bodaghi, M., Zolfonoon, H., Tahriri, M., and Karimi, M.: Synthesis and characterization of nanocrystalline a-Al2O3 using Al and Fe2O3 (hematite) through mechanical alloying. Solid State Sci. 11, 496 (2009).Google Scholar
Khalajabadi, S.Z., Abdul Kadir, M.R., Izman, S., and Mohd Yusop, M.Z.: Facile fabrication of hydrophobic surfaces on mechanically alloyed Mg/HA/TiO2/MgO bionanocomposites. Appl. Surf. Sci. 324, 380 (2015).Google Scholar
Xu, Y.W. and Wang, H.M.: Oxidation behavior of γ/Mo2Ni3Si ternary metal silicide alloy. J. Alloys Compd. 457, 239 (2008).Google Scholar
Wang, Y., Wang, D.Z., Liu, H.Y., Zhu, W., and Zan, X.Q.: Preparation and characterization of sintered molybdenum doped with MoSi2/La2O3/Y2O3 composite particle. Mater. Sci. Eng., A 558, 497 (2012).CrossRefGoogle Scholar
Zan, X.Q., Wang, D.Z., Shi, K.H., Sun, A.K., and Xu, B.: Effect of MoSi2/rare earth composite particles on microstructure and mechanical properties of molybdenum. Int. J. Refract. Met. Hard Mater. 29, 505 (2011).CrossRefGoogle Scholar