Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-26T21:03:41.278Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical characterization of B4C reinforced aluminum matrix composites produced by squeeze casting

Published online by Cambridge University Press:  05 January 2017

Mehmet Ipekoglu ,
Amin Nekouyan ,
Onder Albayrak Open the ORCID record for Onder Albayrak [Opens in a new window]  and
Sabri Altintas
Mehmet Ipekoglu*
Affiliation:
Department of Mechatronic Systems Engineering, Faculty of Engineering, Turkish-German University, Beykoz 34820, Istanbul, Turkey
Amin Nekouyan
Affiliation:
Department of Mechanical Engineering, Faculty of Engineering, Bogazici University, Bebek 34342, Istanbul, Turkey
Onder Albayrak
Affiliation:
Department of Mechanical Engineering, Faculty of Engineering, Mersin University, Yenisehir 33343, Mersin, Turkey
Sabri Altintas
Affiliation:
Department of Mechanical Engineering, Faculty of Engineering, Bogazici University, Bebek 34342, Istanbul, Turkey
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Boron carbide (B4C) ceramic particles were used as reinforcement material to produce aluminum (Al) matrix composites by squeeze casting method. Four different B4C contents as 0, 3, 5, and 10 wt%, and three different squeeze pressures as 0, 75, and 150 MPa were used in which the samples consisted of pure Al without B4C and the samples obtained without applying pressure were used as control samples. To determine the effect of squeezing pressure and the amount of B4C added on machinability and mechanical properties, average chip length and surface roughness of the samples were evaluated and hardness measurements were accomplished, yield and ultimate tensile strengths were determined, respectively. Also, the changes in density and microstructure were investigated. B4C reinforcement was found to decrease the average chip length and density of the samples while increasing the hardness and surface roughness. On the other hand, application of squeeze pressure had a positive effect on the densification and mechanical properties of the samples.

Keywords

Alcompositecasting
Type
Articles
Information
Journal of Materials Research , Volume 32 , Issue 3 , 14 February 2017 , pp. 599 - 605
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Michele Manuel

References

REFERENCES

Chawla, N. and Chawla, K.K.: Metal Matrix Composites (Springer, New York, 2006).CrossRefGoogle Scholar
Koli, D.K., Agnihotri, G., and Purohit, R.: Advanced aluminium matrix composites: The critical need of automotive and aerospace engineering fields. Mater. Today: Proc. 2(4–5), 3032 (2015).Google Scholar
Macke, A., Schultz, B.F., and Rohatgi, P.: Metal matrix composites offer the automotive industry an opportunity to reduce vehicle weight, improve performance. Adv. Mater. Processes 170(3), 19 (2012).Google Scholar
Song, W.Q., Krauklis, P., Mauritz, A.P., and Bandyopadhyay, S.: The effect of thermal ageing on the abrasive behavior of age-hardening Al/SiC and 6061 Al/SiC composites. Wear 185(1–2), 125 (1995).CrossRefGoogle Scholar
Harichandran, R. and Selvakumar, N.: Effect of nano/micro B4C particles on the mechanical properties of aluminium metal matrix composites fabricated by ultrasonic cavitation-assisted solidification process. Arch. Civ. Mech. Eng. 16(1), 147 (2016).CrossRefGoogle Scholar
Wang, Y., Lei, K., Ruan, Y., and Dong, W.: Microstructure and wear resistance of c-BN/Ni–Cr–Ti composites prepared by spark plasma sintering. Int. J. Refract. Met. Hard Mater. 54, 98 (2016).CrossRefGoogle Scholar
Kim, S.B., Koss, D.A., and Gerard, D.A.: High cycle fatigue of squeeze cast Al/SiCw composites. Mater. Sci. Eng., A 277(1–2), 123 (2000).CrossRefGoogle Scholar
Saravanan, L. and Senthilvelan, T.: Investigations on the hot workability characteristics and deformation mechanisms of aluminium alloy-Al2O3 nanocomposite. Mater. Des. 79, 6 (2015).Google Scholar
Takahashi, S., Imai, Y., Kan, A., Hotta, Y., and Ogawa, H.: Improvements in the temperature-dependent properties of dielectric composites by utilizing MgO whiskers as the dielectric filler in an iPP matrix. J. Alloys Compd. 640, 428 (2015).Google Scholar
Sharma, P., Sharma, S., and Khanduja, D.: Production and some properties of Si3N4 reinforced aluminium alloy composites. J. Asian Ceram. Soc. 3(3), 352 (2015).Google Scholar
Johny James, S., Venkatesan, K., Kuppan, P., and Ramanujam, R.: Hybrid aluminium metal matrix composite reinforced with SiC and TiB2 . Procedia Eng. 97, 1018 (2014).CrossRefGoogle Scholar
Chen, K., Hua, Y., Xu, C., Zhang, Q., Qi, C., and Jie, Y.: Preparation of TiC/SiC composites from Ti-enriched slag by an electrochemical process in molten salts. Ceram. Int. 41(9) Part A, 11428 (2015).Google Scholar
Baradeswaran, A., Vettivel, S.C., Perumal, A.E., Selvakumar, N., and Issac, R.F.: Experimental investigation on mechanical behaviour, modelling and optimization of wear parameters of B4C and graphite reinforced aluminium hybrid composites. Mater. Des. 63, 620 (2014).Google Scholar
Jayashree, P.K., Gowri Shankar, M.C., Achutha, K., Sharma, S.S., and Raviraj, S.: Review on effect of silicon carbide (SiC) on stir cast aluminium metal matrix composites. Inter. J. Curr. Eng. Technol. 3(3), 1061 (2013).Google Scholar
Auradi, V., Rajesh, G.L., and Kori, S.A.: Processing of B4C particulate reinforced 6061 aluminum matrix composites by melt stirring involving two-step addition. Procedia Mater. Sci. 6, 1068 (2014).CrossRefGoogle Scholar
Sharifi, E.M., Karimzadeh, F., and Enayati, M.H.: Fabrication and evaluation of mechanical and tribological properties of boron carbide reinforced aluminum matrix nanocomposites. Mater. Des. 32, 3263 (2011).Google Scholar
Poovazhagan, L., Kalaichelvan, K., and Sornakumar, T.: Processing and performance characteristics of aluminum-nano boron carbide metal matrix nanocomposites. Mater. Manuf. Processes 31, 1275 (2016).Google Scholar
Yao, Y.T. and Chen, L.Q.: B4C/Al composites processed by metal-assisted pressureless infiltration technique and its characterization. Mater. Manuf. Processes 31, 1286 (2016).Google Scholar
Shorowordi, K.M., Haseeb, A.S.M.A., and Celis, J.P.: Tribo-surface characteristics of Al–B4C and Al–SiC composites worn under different contact pressures. Wear 261, 634 (2006).CrossRefGoogle Scholar
Lee, K.B., Sim, H.S., Cho, S.Y., and Kwon, H.: Tensile properties of 5052 Al matrix composites reinforced with B4C. Metall. Mater. Trans. A 32, 2142 (2001).CrossRefGoogle Scholar
Ravi, B., Balu Naik, B., and Udaya Prakash, J.: Characterization of aluminium matrix composites (AA6061/B4C) fabricated by stir casting technique. Mater. Today: Proceed. 2(4–5), 2984 (2015).Google Scholar
Skolianos, S.M., Kiourtsidis, G., and Xatzifotiou, T.: Effects of applied pressure on the microstructure and mechanical properties of squeeze-cast AA6061 alloy. Mater. Sci. Eng., A 231(1–2), 17 (1997).Google Scholar
Crouch, I.G.: Aluminium Squeeze Casting Technology, A European Researchers Viewpoint (Australian Conference on Materials for Industrial Development, Christchurch, New Zealand, 1987); p. 24.Google Scholar
Masoumi, M. and Hu, H.: Influence of applied pressure on microstructure and tensile properties of squeeze cast magnesium Mg–Al–Ca Alloy. Mater. Sci. Eng., A 528(10–11), 3589 (2011).Google Scholar
Zhang, Y., Wu, G., Liu, W., Zhang, L., Pang, S., Wang, Y., and Ding, W.: Effects of processing parameters and Ca content on microstructure and mechanical properties of squeeze casting AZ91–Ca alloys. Mater. Sci. Eng., A 595, 109 (2014).Google Scholar
Vijayaram, T.R., Sulaiman, S., Hamouda, A.M.S., and Ahmad, M.H.M.: Fabrication of fiber reinforced metal matrix composites by squeeze casting technology. J. Mater. Process. Technol. 178(1–3), 34 (2006).Google Scholar
Chen, W., Liu, Y., Yang, C., Zhu, D., and Li, Y.: (SiCp+Ti)/7075Al hybrid composites with high strength and large plasticity fabricated by squeeze casting. Mater. Sci. Eng., A 609, 250 (2014).Google Scholar
Bhagat, R.B.: High pressure squeeze casting of stainless steel wire reinforced aluminium matrix composites. Composites 19(5), 393 (1988).Google Scholar
Hu, Q., Zhao, H., and Li, F.: Effects of manufacturing processes on microstructure and properties of Al/A356–B4C composites. Mater. Manuf. Processes 31, 1292 (2016).Google Scholar
Toptan, F., Kilicarslan, A., and Kerti, I.: The effect of Ti addition on the properties of Al–B4C interface: A microstructural study. Mater. Sci. Forum 636–637, 192 (2010).Google Scholar
Baskaya, O.: The mechanical properties and machinability of ZA-27 casting alloys. M.Sc. Thesis, Bogazici University, 2004.Google Scholar
ASTM E8/E8M-09 Standard Test Methods for Tension Testing of Metallic Materials: www.astm.org, 2013.Google Scholar
Ozben, T., Kilickap, E., and Cakır, O.: Investigation of mechanical and machinability properties of SiC particle reinforced Al-MMC. J. Mater. Process. Technol. 198(1–3), 220 (2008).Google Scholar
Baradeswaran, A. and Elaya Perumal, A.: Influence of B4C on the tribological and mechanical properties of Al 7075–B4C composites. Composites, Part B 54, 146 (2013).CrossRefGoogle Scholar
Oluwatosin Bodunrin, M., Alaneme, K.K., and Chown, L.H.: Aluminium matrix hybrid composites: A review of reinforcement philosophies; mechanical, corrosion and tribological characteristics. J. Mater. Res. Technol. 4(4), 434 (2015).Google Scholar
Kashyap, K.T., Ramachandra, C., Dutta, C., and Chatterji, B.: Role of work hardening characteristics of matrix alloys in the strengthening of metal matrix composites. Bull. Mater. Sci. 23(1), 47 (2000).CrossRefGoogle Scholar
Yang, W., Dong, R., Yu, Z., Wu, P., Hussain, M., and Wu, G.: Strengthening behavior in high content SiC nanowires reinforced Al composite. Mater. Sci. Eng., A 648(11), 41 (2015).CrossRefGoogle Scholar
Emamy, S., Vaziri Yeganeh, E., Razaghian, A., and Tavighi, K.: Microstructures and tensile properties of hot-extruded Al matrix composites containing different amounts of Mg2Si. Mater. Sci. Eng., A 586, 190 (2013).Google Scholar
Ezatpour, H.R., Sajjadi, S.A., Sabzevar, M.H., and Huang, Y.: Investigation of microstructure and mechanical properties of Al6061-nanocomposite fabricated by stir casting. Mater. Des. 55, 921 (2014).CrossRefGoogle Scholar