Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-04T21:52:16.085Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical and tribological properties of NiAl–NbC–Ag composites prepared by hot-pressing sintering

Published online by Cambridge University Press:  22 May 2017

Xiaochun Feng ,
Junhong Jia ,
Wenzhen Wang  and
Yu Shan
Xiaochun Feng
Affiliation:
State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, People’s Republic of China; and University of Chinese Academy of Sciences, Beijing 100039, People’s Republic of China
Junhong Jia*
Affiliation:
State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, People’s Republic of China
Wenzhen Wang
Affiliation:
State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, People’s Republic of China
Yu Shan
Affiliation:
State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, People’s Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

NiAl-based nanocomposites were successfully fabricated by mechanical alloying proceeded vacuum-hot-pressing sintering, and the mechanical and tribological properties of the NiA–NbC composite were investigated. The results show that the nanostructured powder particles with the average size around 5 nm were successfully obtained by a high-energy-ball mill. After sintering, the composites were consisted of B2-ordered NiAl and NbC second phase, and the crystalline size of the NiAl phase was about 20 nm. The relative density, hardness, and compressive strength of nanostructured NiAl materials increased with increasing the Nb content, which can be attributed to the second phase hardening effect of in situ formed NbC particulates and fine grain strengthening of nanocrystalline NiAl phase. Thereafter, the friction coefficient of the NiAl–3NbC composite was lowered by the addition of silver and that is significantly lower than the NiAl intermetallic compound and NiAl–3NbC composite at elevated temperatures, which was attributed to the lubricating films formed in sliding process at elevated temperatures. While the wear rates of NiAl–3NbC–10Ag composites are higher than that of the NiAl–3NbC composites at each test temperature, especially at 500 °C and 700 °C, which might be attributed to the phase variations on the worn surfaces of the composites.

Keywords

NiAl intermetallicnanocrystallinemechanical propertytribological performance
Type
Articles
Information
Journal of Materials Research , Volume 32 , Issue 12 , 28 June 2017 , pp. 2361 - 2372
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Darolia, R.: NiAl alloys for high-temperature structural applications. JOM 43, 44 (1991).Google Scholar
Dollar, M., Dymek, S., Hwang, S.J., and Nash, P.: The role of microstructure on strength and ductility of hot-extruded mechanically alloyed NiAl. Metall. Trans. A 24, 1993 (1993).Google Scholar
Liu, E., Gao, Y., Jia, J., Bai, Y., and Wang, W.: Microstructure and mechanical properties of in situ NiAl–Mo2C nanocomposites prepared by hot-pressing sintering. Mater. Sci. Eng., A 592, 201 (2014).Google Scholar
Liu, E., Jia, J., Bai, Y., Wang, W., and Gao, Y.: Study on preparation and mechanical property of nanocrystalline NiAl intermetallic. Mater. Des. 53, 596 (2014).Google Scholar
Liu, E-y., Wang, W-z., Gao, Y-m., and Jia, J-h.: Tribological properties of Ni-based self-lubricating composites with addition of silver and molybdenum disulfide. Tribol. Int. 57, 235 (2013).Google Scholar
Javadi, M.M., Edris, H., and Salehi, M.: Plasma sprayed NiAl intermetallic coating produced with mechanically alloyed powder. J. Mater. Sci. Technol. 27, 816 (2011).Google Scholar
Miracle, D.B.: Overview No. 104 the physical and mechanical properties of NiAl. Acta Metall. Mater. 41, 649 (1993).CrossRefGoogle Scholar
Terada, Y., Ohkubo, K., Mohri, T., and Suzuki, T.: Effects of ternary additions on thermal conductivity of NiAl. Intermetallics 7, 717 (1999).Google Scholar
Whittenberger, J.D., Noebe, R.D., Joslin, S.M., and Oliver, B.F.: Elevated temperature compressive slow strain rate properties of several directionally solidified NiAl–(Nb,Mo) alloys. Intermetallics 7, 627 (1999).Google Scholar
Shi, X., Wang, M., Zhai, W., Xu, Z., Zhang, Q., and Chen, Y.: Influence of Ti3SiC2 content on tribological properties of NiAl matrix self-lubricating composites. Mater. Des. 45, 179 (2013).Google Scholar
Zhu, S., Bi, Q., Niu, M., Yang, J., and Liu, W.: Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures. Wear 274–275, 423 (2012).Google Scholar
Medvedeva, N.I., Gornostyrev, Y.N., Kontsevoi, O.Y., and Freeman, A.J.: Ab initio study of interfacial strength and misfit dislocations in eutectic composites: NiAl/Mo. Acta Mater. 52, 675 (2004).Google Scholar
Fischer, R., Eleno, L.T.F., Frommeyer, G., and Schneider, A.: Precipitation of Cr-rich phases in a Ni–50Al–2Cr (at.%) alloy. Intermetallics 14, 156 (2006).Google Scholar
Ferrandini, P.L., Araujo, F.L.G.U., Batista, W.W., and Caram, R.: Growth and characterization of the NiAl–NiAlNb eutectic structure. J. Cryst. Growth 275, 147 (2005).Google Scholar
Guo, J.T., Huai, K.W., Gao, Q., Ren, W.L., and Li, G.S.: Effects of rare earth elements on the microstructure and mechanical properties of NiAl-based eutectic alloy. Intermetallics 15, 727 (2007).Google Scholar
Guo, J.T., Sheng, L.Y., Tian, Y.X., Zhou, L.Z., and Ye, H.Q.: Effect of Ho on the microstructure and compressive properties of NiAl-based eutectic alloy. Mater. Lett. 62, 3910 (2008).Google Scholar
Chen, Y. and Wang, H.M.: Laser melted TiC reinforced nickel aluminide matrix in situ composites. J. Alloys Compd. 391, 49 (2005).CrossRefGoogle Scholar
Dercz, G., Pająk, L., and Formanek, B.: Dispersion analysis of NiAl–TiC–Al2O3 composite powder ground in a high-energy attritorial mill. J. Mater. Process. Technol. 175, 334 (2006).Google Scholar
Yu, L.G., Dai, J.Y., Xing, Z.P., Li, D.X., Guo, J.T., and Ye, H.Q.: High resolution electron microscopy observation of interfacial structures in NiAl-matrix in situ composites reinforced by TiC particulates. J. Mater. Res. 12, 1790 (1997).Google Scholar
Guo, J.T. and Xing, Z.P.: Investigation of NiAl–TiB2 in situ composites. J. Mater. Res. 12, 1083 (1997).Google Scholar
Xing, Z.P., Han, Y.F., Guo, J.T., and Yu, L.G.: Microstructure and mechanical behavior of the NiAl–TiC in situ composite. Metall. Mater. Trans. A 28, 1079 (1997).Google Scholar
Bochenek, K. and Basista, M.: Advances in processing of NiAl intermetallic alloys and composites for high temperature aerospace applications. Prog. Aeronaut. Sci. 79, 136 (2015).Google Scholar
Albiter, A., Salazar, M., Bedolla, E., Drew, R.A.L., and Perez, R.: Improvement of the mechanical properties in a nanocrystalline NiAl intermetallic alloy with Fe, Ga and Mo additions. Mater. Sci. Eng., A 347, 154 (2003).Google Scholar
Joardar, J., Pabi, S.K., and Murty, B.S.: Milling criteria for the synthesis of nanocrystalline NiAl by mechanical alloying. J. Alloys Compd. 429, 204 (2007).CrossRefGoogle Scholar
Moshksar, M.M. and Mirzaee, M.: Formation of NiAl intermetallic by gradual and explosive exothermic reaction mechanism during ball milling. Intermetallics 12, 1361 (2004).Google Scholar
Stone, D.S., Migas, J., Martini, A., Smith, T., Muratore, C., and Voevodin, A.A.: Adaptive NbN/Ag coatings for high temperature tribological applications. Surf. Coat. Technol. 206, 4316 (2012).Google Scholar
Cotton, J.D., Noebe, R.D., and Kaufman, M.J.: Ternary Alloying Effects in Polycrystalline β-NiAl. In International Symposium on Structural Intermetallics, Vol. 513, Doralia, R., Lewandowski, J.J., Liu, C.T., and Martin, P.L., eds. (TMS, Warrendale, 1993); pp. 1–16.Google Scholar
Mao, S.X., McMinn, N.A., and Wu, N.Q.: Processing and mechanical behaviour of TiAl/NiAl intermetallic composites produced by cryogenic mechanical alloying. Mater. Sci. Eng., A 363(1–2), 275 (2003).CrossRefGoogle Scholar
Guo, J.T., Zhou, L.Z., and Li, G.S.: Mechanically synthesis and mechanical properties of nanocrystalline intermetallics NiAl. Acta Metall. Sin. 35, 846 (1999).Google Scholar
Liu, F. and Jia, J.: Tribological properties and wear mechanisms of NiCr–Al2O3–SrSO4–Ag self-lubricating composites at elevated temperatures. Tribol. Lett. 49, 281 (2013).Google Scholar
Williams, J.A.: Wear and wear particles—Some fundamentals. Tribol. Int. 38, 863 (2005).Google Scholar
Liu, E., Bai, Y., Gao, Y., Yi, G., and Jia, J.: Tribological properties of NiAl-based composites containing Ag3VO4 nanoparticles at elevated temperatures. Tribol. Int. 80, 25 (2014).Google Scholar
Loukil, A., Boukhachem, A., Ben Amor, M., Ghamnia, M., and Raouadi, K.: Effects of potassium incorporation on the structural, optical, vibrational and electrical properties of NiO sprayed thin films for p-type optical windows. Ceram. Int. 42, 8274 (2016).Google Scholar
Mrabet, C., Ben Amor, M., Boukhachem, A., Amlouk, M., and Manoubi, T.: Physical properties of La-doped NiO sprayed thin films for optoelectronic and sensor applications. Ceram. Int. 42, 5963 (2016).Google Scholar
Muratore, C., Bultman, J.E., Aouadi, S.M., and Voevodin, A.A.: In situ Raman spectroscopy for examination of high temperature tribological processes. Wear 270, 140 (2011).Google Scholar
Yuan, C., Zhou, L., Li, G., and Guo, J.: Characteristics of A NiAl eutectic alloy JJ-3 with excellent properties. Acta Metall. Sin. 49, 1347 (2013).Google Scholar
Menezes, P.L., Nosonovsky, M., Ingole, S.P., Kailas, S.V., and Lovell, M.R.: Tribology for Scientists and Engineers: From Basics to Advanced Concepts (Springer, Berlin, 2013).Google Scholar
Liu, E., Gao, Y., Bai, Y., Yi, G., Wang, W., and Zeng, Z.: Tribological properties of self-lubricating NiAl/Mo-based composites containing AgVO3 nanowires. Mater. Charact. 97, 116 (2014).Google Scholar
Ju, H. and Xu, J.: Microstructure and tribological properties of NbN–Ag composite films by reactive magnetron sputtering. Appl. Surf. Sci. 355, 878 (2015).Google Scholar