Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-26T08:24:51.878Z Has data issue: false hasContentIssue false
  • English
  • Français

Identification of delamination through TGO stresses due to indentation testing of an EB-PVD TBC

Published online by Cambridge University Press:  31 January 2011

Makoto Tanaka ,
Yu-Fu Liu  and
Yutaka Kagawa
Yutaka Kagawa*
Affiliation:
Research Center for Advanced Science and Technology, The University of Tokyo, Tokyo 153-8904, Japan
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The Rockwell indentation test was used to generate interface delamination in an EB-PVD thermal barrier coating (TBC) system that was thermally cycled between 300 °C and 1050 °C. Luminescence spectroscopy was applied to measure the thermally grown oxide (TGO) stresses in indentation-affected and perfectly bonded regions. Comparison between experimental stress mapping in bonded and delaminated regions by luminescence spectroscopy and finite element analysis was shown and the effect of delamination paths was presented. Zigzag delamination paths alternating between the top TBC-TGO interface and TGO-bond coat interface were shown to induce TGO stress releases and fluctuations in the delaminated region. Luminescence spectroscopy measurements successfully detect such behavior, making it possible to identify nondestructively the size of the delaminated region, the delamination crack front position, and the delamination paths in part.

Keywords

CoatingLuminescence
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 12 , December 2009 , pp. 3533 - 3542
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Padture, N.P., Gell, M., and Jordan, E.H.: Thermal-barrier coatings for gas-turbine engine applications. Science 296, 280 (2002).CrossRefGoogle ScholarPubMed
2.Clarke, D.R. and Levi, C.G.: Materials design for the next generation thermal-barrier coatings. Annu. Rev. Mater. Res. 33, 383 (2003).CrossRefGoogle Scholar
3.Evans, A.G., Clarke, D.R., and Levi, C.G.: The influence of oxides on the performance of advanced gas turbines. J. Eur. Ceram. Soc. 28, 1405 (2008).CrossRefGoogle Scholar
4.Evans, A.G., Mumm, D.R., Hutchinson, J.W., Meier, G.H., and Pettit, F.S.: Mechanisms controlling the durability of thermal-barrier coatings. Prog. Mater. Sci. 46, 505 (2001).CrossRefGoogle Scholar
5.Newaz, G. and Chen, X.: Progressive damage assessment in thermal-barrier coatings using thermal wave imaging technique. Surf. Coat. Technol. 190, 7 (2005).CrossRefGoogle Scholar
6.Franke, B., Sohn, Y.H., Chen, X., Price, J.R., and Mutasim, Z.: Monitoring damage evolution in thermal-barrier coatings with thermal wave imaging. Surf. Coat. Technol. 200, 1292 (2005).CrossRefGoogle Scholar
7.Mesrati, N., Saif, Q., Treheux, D., Moughil, A., Fantozzi, G., and Vincent, A.: Characterization of thermal fatigue damage of thermal barrier produced by atmospheric plasma spraying. Surf. Coat. Technol. 187, 185 (2004).CrossRefGoogle Scholar
8.Tolpygo, V.K., Clarke, D.R., and Murphy, K.S.: Evaluation of interface degradation during cyclic oxidation of EB-PVD thermal-barrier coatings and correlation with TGO luminescence. Surf. Coat. Technol. 188–189, 62 (2004).CrossRefGoogle Scholar
9.Sergo, V. and Clarke, D.R.: Observation of subcritical spall propagation of a thermal barrier coating. J. Am. Ceram. Soc. 81, 3237 (1998).CrossRefGoogle Scholar
10.Selçuk, A. and Atkinson, A.: Analysis of the Cr3+ luminescence spectra from thermally grown oxide in thermal-barrier coatings. Mater. Sci. Em., A 335, 147 (2002).Google Scholar
11.Selçuk, A. and Atkinson, A.: The evolution of residual stress in the thermally grown oxide on Pt diffusion bond coats in TBCs. Acta Mater. 51, 535 (2003).CrossRefGoogle Scholar
12.Mumm, D.R., Evans, A.G., and Spitsberg, I.T.: Characterization of a cyclic displacement instability for a thermally grown oxide in a thermal barrier system. Acta Mater. 49, 2329 (2001).CrossRefGoogle Scholar
13.Balint, D.S. and Hutchinson, J.W.: An analytical model of rumpling in thermal-barrier coatings. J. Mech. Phys. Solids 53, 949 (2005).CrossRefGoogle Scholar
14.Peng, X. and Clarke, D.R.: Piezospectroscopic analysis of interface debonding in thermal-barrier coatings. J. Am. Ceram. Soc. 83, 1165 (2000).CrossRefGoogle Scholar
15.Tolpygo, V.K. and Clarke, D.R.: Spalling failure of a-alumina films grown by oxidation: I. Dependence on cooling rate and metal thickness. Mater. Sci. Eng., A 278, 142 (2000).CrossRefGoogle Scholar
16.Mumm, D.R. and Evans, A.G.: On the role of imperfections in the failure of a thermal barrier coating made by electron beam deposition. Acta Mater. 48, 1815 (2000).CrossRefGoogle Scholar
17.Begley, M.R., Mumm, D.R., Evans, A.G., and Hutchinson, J.W.: Analysis of a wedge impression test for measuring the interface toughness between films/coatings and ductile substrates. Acta Mater. 48, 3211 (2000).CrossRefGoogle Scholar
18.Vasinonta, A. and Beuth, J.L.: Measurement of interfacial toughness in thermal barrier coating systems by indentation. Em. Fract. Mech. 68, 843 (2001).CrossRefGoogle Scholar
19.Chen, X., Wang, R., Yao, N., Evans, A.G., Hutchinson, J.W., and Bruce, R.W.: Foreign object damage in a thermal barrier system: Mechanisms and simulations. Mater. Sci. Eng., A 352, 221 (2003).CrossRefGoogle Scholar
20.Watanabe, M., Mercer, C., Levi, C.G., and Evans, A.G.: A probe for the high temperature deformation of thermal barrier oxides. Acta Mater. 52, 1479 (2004).CrossRefGoogle Scholar
21.Tomimatsu, T., Zhu, S., and Kagawa, Y.: Effect of thermal exposure on stress distribution in TGO layer of EB-PVD TBC. Acta Mater. 51, 2397 (2003).CrossRefGoogle Scholar
22.Tanaka, M., Hasegawa, M., and Kagawa, Y.: Detection of micro-damage evolution of air plasma-sprayed Y2O3-ZrO2 thermal barrier coating through TGO stress measurement. Mater. Trans. 47, 2512 (2006).CrossRefGoogle Scholar
23.Yan, J., Leist, T., Bartsch, M., and Karlsson, A.M.: On cracks and delaminations of thermal-barrier coatings due to indentation testing: Experimental investigations. Acta Mater. 56, 4080 (2008).CrossRefGoogle Scholar
24.Bartsch, M., Mircea, I., Suffner, J., and Baufeld, B.: Interfacial fracture toughness measurement of thick ceramic coatings by indentation. Key Em. Mater. 290, 183 (2005).CrossRefGoogle Scholar
25.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
26.Malzbender, J. and Steinbrech, R.W.: Determination of the stress-dependent stiffness of plasma-sprayed thermal-barrier coatings using depth-sensitive indentation. J. Mater. Res. 18, 1975 (2003).CrossRefGoogle Scholar
27.He, J. and Clarke, D.R.: Determination of the piezospectroscopic coefficients for chromium-doped sapphire. J. Am. Ceram. Soc. 78, 1347 (1995).CrossRefGoogle Scholar
28.Tomimatsu, T., Zhu, S.J., and Kagawa, Y.: Local stress distribution in thermally-grown-oxide layer by near-field optical microscopy. Scr. Mater. 50, 137 (2004).CrossRefGoogle Scholar
29.Yu, H.Y., Sanday, S.C., and Rath, B.B.: The effect of substrate on the elastic properties of films determined by the indentation test-Axisymmetric Boussinesq problem. J. Mech. Phys. Solids 38, 745 (1990).CrossRefGoogle Scholar
30. ABAQUS User's Manuals, ABAQUS Inc., Providence, RI, 2006.Google Scholar
31.Kim, S.S., Liu, Y.F., and Kagawa, Y.: Evaluation of interfacial mechanical properties under shear loading in EB-PVD TBCs by the pushout method. Acta Mater. 55, 3771 (2007).CrossRefGoogle Scholar
32.Tanaka, M., Liu, Y.F., Kim, S.S., and Kagawa, Y.: Delamination toughness of electron beam physical vapor deposition (EB-PVD) Y2O3-ZrO2 thermal-barrier coatings by the pushout method: Effect of thermal cycling temperature. J. Mater. Res. 23, 2382 (2008).CrossRefGoogle Scholar