Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-25T18:07:07.077Z Has data issue: false hasContentIssue false
  • English
  • Français

Formation of low-angle grain boundaries under different solidification conditions in the rejoined platforms of Ni-based single crystal superalloys

Published online by Cambridge University Press:  09 November 2018

Miao Huo Open the ORCID record for Miao Huo [Opens in a new window] ,
Lin Liu ,
Wenchao Yang Open the ORCID record for Wenchao Yang [Opens in a new window] ,
Yafeng Li ,
Songsong Hu ,
Haijun Su ,
Jun Zhang  and
Hengzhi Fu
Miao Huo
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Lin Liu*
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Wenchao Yang*
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Yafeng Li*
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Songsong Hu
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Haijun Su
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Jun Zhang
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
Hengzhi Fu
Affiliation:
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
*
a)Address all correspondence to these authors. e-mail: [email protected]
b)e-mail: [email protected]
Get access

Abstract

The formation of low-angle grain boundaries (LABs) in the rejoined platforms of a Ni-based single crystal superalloy under different directional solidification rates was investigated by the experimental investigation and the ProCAST simulation. The results showed that the growth morphology and orientation evolution of dendrites in the platforms were different under the withdrawal rates in the range of 60–100 μm/s and then resulted in different types of LABs. At lower withdrawal rates, the longitudinal LABs were common in the rejoined platforms. Both the sliver defects and the orientation deviation of original primary dendrites from two independent growth paths could cause the longitudinal LABs in the platforms. At higher withdrawal rates, the dendrite growth patterns were more complex and the secondary branches with lateral growth tended to deviate from their original orientation, eventually leading to the formation of some transverse LABs. Finally, some suggestions to prevent the formation of different LABs are provided.

Keywords

Ni-based superalloyslow angle grain boundaries (LABs)sliversolidification conditions
Type
Article
Information
Journal of Materials Research , Volume 34 , Issue 2 , 28 January 2019 , pp. 251 - 260
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Reed, R.C.: The Superalloys Fundamentals and Applications, 1st ed. (Cambridge University Press, Cambridge, England, 2006); p. 4.CrossRefGoogle Scholar
Pollock, T.M. and Tin, S.: Nickel-based superalloys for advanced turbine engines: Chemistry, microstructure and properties. J. Propul. Power 22, 361 (2006).CrossRefGoogle Scholar
Rahimian, M., Milenkovic, S., and Sabirov, I.: Microstructure and hardness evolution in MAR-M247 Ni-based superalloy processed by controlled cooling and double heat treatment. J. Alloys Compd. 550, 339 (2013).CrossRefGoogle Scholar
Graverend, J.B.L., Jacques, A., Cormier, J., Ferry, O., Schenk, T., and Mendez, J.: Creep of a nickel-based single-crystal superalloy during very high-temperature jumps followed by synchrotron X-ray diffraction. Acta Mater. 84, 65 (2015).CrossRefGoogle Scholar
Yeh, A.C. and Tin, S.: Effects of Ru and Re additions on the high temperature flow stresses of Ni-base single crystal superalloys. Scr. Mater. 52, 519 (2005).CrossRefGoogle Scholar
Tin, S., Pollock, T.M., and Murphy, W.: Stabilization of thermosolutal convective instabilities in Ni-based single-crystal superalloys: Carbon additions and freckle formation. Metall. Mater. Trans. A 32, 1743 (2001).CrossRefGoogle Scholar
Li, Q.D., Shen, J., Qin, L., and Gao, S.X.: Investigation on freckles in directionally solidified CMSX-4 superalloy specimens with abrupt cross section variation. J. Alloys Compd. 691, 997 (2017).CrossRefGoogle Scholar
Vehn, M.M.T., Dedecke, D., Paul, U., and Sahm, P.R.: Undercooling related casting defects in single crystal turbine blades. In Superalloys 1996, Kissinger, R.D., Deye, D.J., Anton, D.L., Cetel, A.D., Nathal, M.V., Pollock, T.M., and Woodford, D.A., eds. (TMS: Warrendale, 1996); p. 471.Google Scholar
Yang, X.L., Dong, H.B., Wang, W., and Lee, P.D.: Microscale simulation of stray grain formation in investment cast turbine blades. Mater. Sci. Eng., A 386, 129 (2004).CrossRefGoogle Scholar
Aveson, J.W., Tennant, P.A., Foss, B.J., Shollock, B.A., Stone, H.J., and D’Souza, N.: On the origin of sliver defects in single crystal investment castings. Acta Mater. 61, 5162 (2013).CrossRefGoogle Scholar
Newell, M., D’Souza, N., and Green, N.R.: Formation of low angle boundaries in Ni-based superalloys. Mater. Sci. Eng., A 413, 567 (2005).Google Scholar
Bogdanowicz, W., Albrecht, R., Sieniawski, J., and Kubiak, K.: The subgrain structure in turbine blade roots of CMSX-4 superalloy. J. Cryst. Growth 401, 418 (2014).CrossRefGoogle Scholar
Li, J.R., Zhao, J.Q., Liu, S.Z., and Han, M.: Effects of low angle boundaries on the mechanical properties of single crystal superalloy DD6. In Superalloys 2008, Reed, R.C., Green, K.A., Caron, P., Gabb, T.P., Fahrmann, M.G., Huron, E.S., and Woodard, S.A., eds. (TMS: Warrendale, 2008); p. 443.Google Scholar
Zhao, J.Q., Li, J.R., Liu, S.Z., and Han, M.: Effects of low angle grain boundaries on stress rupture properties of single crystal superalloy DD6. J. Mater. Eng. 27, 6 (2007).Google Scholar
Napolitano, R.E. and Schaefer, R.J.: The convergence-fault mechanism for low-angle boundary formation in single-crystal castings. J. Mater. Sci. 35, 1641 (2000).CrossRefGoogle Scholar
Newell, M., Devendra, K., Jennings, P.A., and D’Souza, N.: Role of dendrite branching and growth kinetics in the formation of low angle boundaries in Ni-base superalloys. Mater. Sci. Eng., A 412, 307 (2005).CrossRefGoogle Scholar
Newell, M., D’Souza, N., and Green, N.R.: Formation of low angle boundaries in Ni-based superalloys. Int. J. Cast Met. Res. 22, 66 (2009).CrossRefGoogle Scholar
Siredey, N., Boufoussi, M., Denis, S., and Lacaze, J.: Dendritic growth and crystalline quality of nickel-base single grains. J. Cryst. Growth 130, 132 (1993).CrossRefGoogle Scholar
Dragnevski, K., Mullis, A.M., Walker, D.J., and Cochrane, R.F.: Mechanical deformation of dendrites by fluid flow during the solidification of undercooled melts. Acta Mater. 50, 3743 (2002).CrossRefGoogle Scholar
Wang, F., Wu, Z., Huang, C., Ma, D., Jakumeit, J., and Bührig-Polaczek, A.: Three-dimensional dendrite growth within the shrouds of single crystal blades of a nickel-based superalloy. Metall. Mater. Trans. A 48, 5924 (2017).CrossRefGoogle Scholar
Ma, D.X.: Development of single crystal solidification technology for production of superalloy turbine blades. Acta Metall. Sin. 51, 1179 (2015).Google Scholar
Gandin, C.A., Rappaz, M., and Tintillier, R.: Three-dimensional probabilistic simulation of solidification grain structure: Application to superalloy precision castings. Metall. Mater. Trans. A 24, 467 (1993).CrossRefGoogle Scholar
Miller, J.D. and Pollock, T.M.: The effect of processing conditions on heat transfer during directional solidification via the bridgman and liquid metal cooling processes. Metall. Mater. Trans. A 45, 411 (2014).CrossRefGoogle Scholar
Li, Y.F., Liu, L., Huang, T.W., Huo, M., He, J.S., Zhang, J., and Fu, H.Z.: Simulation of stray grain formation in Ni-base single crystal turbine blades fabricated by HRS and LMC techniques. China Foundry 14, 75 (2017).CrossRefGoogle Scholar
Wang, N., Liu, L., Gao, S.F., Zhao, X.B., Huang, T.W., Zhang, J., and Fu, H.Z.: Simulation of grain selection during single crystal casting of a Ni-base superalloy. J. Alloys Compd. 586, 220 (2014).CrossRefGoogle Scholar
Li, Y.F., Liu, L., Huang, T.W., Sun, D.J., Zhang, J., and Fu, H.Z.: The formation mechanism, influencing factor and processing control of stray grains in nickel-based single crystal superalloys. In Superalloys 2016, Hardy, M., Huron, E., Glatzel, U., Griffin, B., Lewis, B., Rae, C., Seetharaman, V., and Tin, S., eds. (TMS: Warrendale, 2016); p. 293.CrossRefGoogle Scholar
Brundidge, C.L., Miller, J.D., and Pollock, T.M.: Development of dendritic structure in the liquid-metal-cooled, directional-solidification process. Metall. Mater. Trans. A 42, 2723 (2011).CrossRefGoogle Scholar
Huo, M., Liu, L., Yang, W.C., Sun, D.J., Hu, S.S., Zhang, J., and Fu, H.Z.: Formation of slivers in the extended cross-section platforms of Ni-based single crystal superalloy. Adv. Eng. Mater. 20, 1701189 (2018).CrossRefGoogle Scholar
D’Souza, N., Ardakani, M.G., Mclean, M., and Shollock, B.A.: Directional and single-crystal solidification of Ni-base superalloys: Part I. The role of curved isotherms on grain selection. Metall. Mater. Trans. A 31, 2877 (2000).CrossRefGoogle Scholar
Hu, S.S., Yang, W.C., Cui, Q.W., Huang, T.W., Zhang, J., and Liu, L.: Effect of secondary dendrite orientations on competitive growth of converging dendrites of Ni-based bi-crystal superalloys. Mater. Charact. 125, 152 (2017).CrossRefGoogle Scholar
Zhou, Y.Z. and Sun, X.F.: Effect of solidification rate on competitive grain growth in directional solidification of a nickel-base superalloy. Sci. China: Technol. Sci. 55, 1327 (2012).CrossRefGoogle Scholar
Miller, J.D. and Pollock, T.M.: Stability of dendrite growth during directional solidification in the presence of a non-axial thermal field. Acta Mater. 78, 23 (2014).CrossRefGoogle Scholar
Miller, J.D., Yuan, L., Lee, P.D., and Pollock, T.M.: Simulation of diffusion-limited lateral growth of dendrites during solidification via liquid metal cooling. Acta Mater. 69, 47 (2014).CrossRefGoogle Scholar
Zhang, X.L., Zhou, Y.Z., Han, Y.Y., Jin, T., and Sun, X.F.: Dendritic growth pattern and dendritic network distortion in the platform of a Ni-based superalloy. J. Mater. Sci. Technol. 30, 223 (2014).CrossRefGoogle Scholar