Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-19T08:26:57.220Z Has data issue: false hasContentIssue false
  • English
  • Français

Finite element analysis and experimental investigation of the Hertzian assumption on the characterization of initial plastic yield

Published online by Cambridge University Press:  31 January 2011

Li Ma ,
Dylan J. Morris ,
Stefhanni L. Jennerjohn ,
David F. Bahr  and
Lyle Levine
Li Ma
Affiliation:
National Institute of Standards and Technology, Materials Science and Engineering Laboratory, Gaithersburg, Maryland 20899-8520; and Department of Chemical Physics, Kent State University, Kent, Ohio 44242
Dylan J. Morris
Affiliation:
National Institute of Standards and Technology, Materials Science and Engineering Laboratory, Gaithersburg, Maryland 20899-8520
Stefhanni L. Jennerjohn
Affiliation:
National Institute of Standards and Technology, Materials Science and Engineering Laboratory, Gaithersburg, Maryland 20899-8520; and Department of Chemical Physics, Kent State University, Kent, Ohio 44242
David F. Bahr
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164
Lyle Levine
Affiliation:
National Institute of Standards and Technology, Materials Science and Engineering Laboratory, Gaithersburg, Maryland 20899-8520
Get access

Abstract

Sudden displacement excursions during load-controlled nanoindentation of relatively dislocation-free surfaces of metals are frequently associated with dislocation nucleation, multiplication, and propagation. Insight into the nanomechanical origins of plasticity in metallic crystals may be gained through estimation of the stresses that nucleate dislocations. An assessment of the potential errors in the experimental measurement of nucleation stresses, especially in materials that exhibit the elastic–plastic transition at small indentation depths, is critical. In this work, the near-apex shape of a Berkovich probe was measured by scanning probe microscopy. This shape was then used as a “virtual” indentation probe in a 3-dimensional finite element analysis (FEA) of indentation on 〈100〉-oriented single-crystal tungsten. Simultaneously, experiments were carried out with the real indenter, also on 〈100〉-oriented single-crystal tungsten. There is good agreement between the FEA and experimental load–displacement curves. The Hertzian estimate of the radius of curvature was significantly larger than that directly measured from the scanning probe experiments. This effect was replicated in FEA simulation of indentation by a sphere. These results suggest that Hertzian estimates of the maximum shear stresses in the target material at the point of dislocation nucleation are a conservative lower bound. Stress estimates obtained from the experimental data using the Hertzian approximation were over 30% smaller than those determined from FEA.

Keywords

DislocationsNanoindentation
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 1059 - 1068
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Gane, N. and Bowden, F.P.: Microdeformation of solids. J. Appl. Phys. 39, 1432 (1968).CrossRefGoogle Scholar
2.Morris, D.J., Myers, S.B., and Cook, R.F.: Sharp probes of varying acuity: Instrumented indentation and fracture behavior. J. Mater. Res. 19, 165 (2004).CrossRefGoogle Scholar
3.Jungk, J.M., Boyce, B.L., Buchheit, T.E., Friedmann, T.A., Yang, D., and Gerberich, W.W.: Indentation fracture toughness and acoustic energy release in tetrahedral amorphous carbon diamond-like thin films. Acta Mater. 54, 4043 (2006).CrossRefGoogle Scholar
4.Page, T.F., Oliver, W.C., and McHargue, C.J.: The deformation behavior of ceramic crystals subjected to very low load (nano) indentations. J. Mater. Res. 7, 450 (1992).CrossRefGoogle Scholar
5.Cross, G.L.W., Schirmeisen, A., Grutter, P., and Durig, U.T.: Plasticity, healing and shakedown in sharp-asperity nanoindent-ation. Nat. Mater. 5, 370 (2006).CrossRefGoogle Scholar
6.Juliano, T., Domnich, V., and Gogotsi, Y.: Examining pressure-induced phase transformations in silicon by spherical indentation and Raman spectroscopy: A statistical study. J. Mater. Res. 19, 3099 (2004).CrossRefGoogle Scholar
7.Warren, O.L., Downs, S.A., and Wyrobek, T.J.: Challenges and interesting observations associated with feedback-controlled nanoindentation. Z. Metallkd. 95, 287 (2004).CrossRefGoogle Scholar
8.Kiely, J.D. and Houston, J.E.: Nanomechanical properties of Au (111), (001), and (110) surfaces. Phys. Rev. B 57, 12588 (1998).CrossRefGoogle Scholar
9.Bradby, J.E., Williams, J.S., and Swain, M.V.: Pop-in events induced by spherical indentation in compound semiconductors. J. Mater. Res. 19, 380 (2004).CrossRefGoogle Scholar
10.Schuh, C.A., Mason, J.K., and Lund, A.C.: Quantitative insight into dislocation nucleation from high-temperature nanoindentation experiments. Nat. Mater. 4, 617 (2005).CrossRefGoogle ScholarPubMed
11.Mann, A.B. and Pethica, J.B.: Role of atomic size asperities in the mechanical deformation of nanocontacts. Appl. Phys. Lett. 69, 907 (1996).CrossRefGoogle Scholar
12.Gerberich, W.W., Nelson, J.C., Lilleodden, E.T., Anderson, P., and Wyrobek, J.T.: Indentation induced dislocation nucleation: The initial yield point. Acta Mater. 44, 3585 (1996).CrossRefGoogle Scholar
13.Syed Asif, S.A. and Pethica, J.B.: Nanoindentation creep of single-crystal tungsten and gallium arsenide. Philos. Mag. A 76, 1105 (1997).CrossRefGoogle Scholar
14.Bahr, D.F., Kramer, D.E., and Gerberich, W.W.: Non-linear deformation mechanisms during nanoindentation. Acta Mater. 46, 3605 (1998).CrossRefGoogle Scholar
15.Chiu, Y.L. and Ngan, A.H.W.: Time-dependent characteristics of incipient plasticity in nanoindentation of a Ni3Al single crystal. Acta Mater. 50, 1599 (2002).CrossRefGoogle Scholar
16.Minor, A.M., Syed Asif, S.A., Shan, Z., Stach, E.A., Cyrankowski, E., Wyrobek, T.J., and Warren, O.L.: A new view of the onset of plasticity during the nanoindentation of aluminium. Nat. Mater. 5, 697 (2006)CrossRefGoogle ScholarPubMed
17.Minor, A.M., Lilleodden, E.T., Stach, E.A., and Morris, J.W. Jr: Direct observations of incipient plasticity during nanoindentation of Al. J. Mater. Res. 19, 176 (2004).CrossRefGoogle Scholar
18.Van Vliet, K.J., Li, J., Zhu, T., Yip, S., and Suresh, S.: Quantifying the early stages of plasticity through nanoscale experiments and simulations. Phys. Rev. B 67, 104105 (2003).CrossRefGoogle Scholar
19.Thurn, J. and Cook, R.F.: Simplified area function for sharp in-denter tips in depth-sensing indentation. J. Mater. Res. 17, 1143 (2002).CrossRefGoogle Scholar
20.Shih, C.W., Yang, M., and Li, J.C.M.: Effect of tip radius on nanoindentation. J. Mater. Res. 6, 2623 (1991).CrossRefGoogle Scholar
21.Seitzman, L.E.: Mechanical properties from instrumented indentation: Uncertainties due to tip-shape correction. J. Mater. Res. 13, 2936 (1998).CrossRefGoogle Scholar
22.Johnson, K.L.: Contact Mechanics (Cambridge University Press, Cambridge, UK, 1999).Google Scholar
23.Ma, L. and Levine, L.E.: Effect of the spherical indenter tip assumption on nanoindentation. J. Mater. Res. 22, 1656 (2007).CrossRefGoogle Scholar
24.Aldrich-Smith, G., Jennett, N.M., and Hangen, U.: Direct measurement of nanoindentation area function by metrological AFM. Z. Metallkd. 96, 1267 (2005).CrossRefGoogle Scholar
25.Constantinides, G., Silva, E.C.C.M., Blackman, G.S., and Van Vliet, K.J.: Dealing with imperfection: Quantifying potential length scale artefacts from nominally spherical indenter probes. Nano-technoloffv 18, 305503 (2007).Google Scholar
26.Zbib, A.A. and Bahr, D.F.: Dislocation nucleation and source activation during nanoindentation yield points. Metall. Mater. Trans. A 38, 2249 (2007).CrossRefGoogle Scholar
27.Vander, G.F. Voort: Metallography: Principles and Practice (McGraw-Hill, New York, 1984).CrossRefGoogle Scholar
28.Wagner, R.J., Ma, L., Tavazza, F., and Levine, L.E.: Dislocation nucleation during nanoindentation of aluminum. J. Appl. Phys. 104, 114311 (2008).CrossRefGoogle Scholar
29.CRC Handbook of Chemistry and Physics, edited by D.R. Lide (CRC Press, Boca Raton, FL, 2007).Google Scholar
30.Tyulyukovskiy, E. and Huber, N.: Neural networks for tip correction of spherical indentation curves from bulk metals and thin metal films. J. Mech. Phys. Solids 55, (2007).Google Scholar
31.Vlassak, J.J., Ciavarella, M., Barber, J.R., and Wang, X.: The indentation modulus of elastically anisotropic materials for indenters of arbitrary shape. J. Mech. Phys. Solids 51, 1701 (2003).CrossRefGoogle Scholar
32.Bei, H., George, E.P., Hay, J.L., and Pharr, G.M.: Influence of indenter tip geometry on elastic deformation during nanoindenta-tion. Phys. Rev. Lett. 95, 045501 (2005).CrossRefGoogle Scholar
33.Briscoe, B.J., Sebastian, K.S., and Adams, M.J.: Effect of indenter geometry on the elastic response to indentation. J. Phys. D 27, 1156 (1994).CrossRefGoogle Scholar
34.Yoffe, E.H.: Modified Hertz theory for spherical indentation. Philos. Mag. A 50, 813 (1984).CrossRefGoogle Scholar
35.Storey, C.: Investigation into one of the assumptions of the Hertz theory of contact. Br. J. Appl. Phys. 11, 67 (1960).CrossRefGoogle Scholar
36.Schwarzer, N.: Elastic surface deformation due to indenters with arbitrary symmetry of revolution. J. Phys. D 37, 2761 (2004).CrossRefGoogle Scholar
37.Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
38.Maugis, D.: Extension of the Johnson-Kendall-Roberts theory of the elastic contact of spheres to large contact radii. Langmuir 11. 679 (1995).CrossRefGoogle Scholar
39.Goodman, L.E. and Keer, L.M.: The contact stress problem for an elastic sphere indenting an elastic cavity. Int. J. Solids Struct. 1, 407 (1965).CrossRefGoogle Scholar
40.Johnson, K.L.: One hundred years of Hertz contact. Proc. Inst. Mech. Eng. 196, 363 (1982).CrossRefGoogle Scholar
41.Hay, J.L. and Wolff, P.J.: Small correction required when applying the Hertzian contact model to instrumented indentation data. J. Mater. Res. 16, 1280 (2001).CrossRefGoogle Scholar
42.Tatara, Y., Shima, S., and Lucero, J.C.: On compression of rubber elastic sphere over a large range of displacements. Part 2. Comparison of theory and experiment. J. Eng. Mater. TASME 113, 292 (1991).CrossRefGoogle Scholar
43.Bai, Z. and Shield, R.T.: Load-deformation relations in second-order elasticity. ZAMP 46, 479 (1995).Google Scholar