Hostname: page-component-cd9895bd7-dzt6s Total loading time: 0 Render date: 2024-12-23T11:47:02.216Z Has data issue: false hasContentIssue false
  • English
  • Français

Extensive deformation behavior of an all-oxide Al2O3-TiO2 nanostructured multilayer ceramic at room temperature

Published online by Cambridge University Press:  31 January 2011

Arcan F. Dericioglu ,
Y.F. Liu  and
Yutaka Kagawa
Arcan F. Dericioglu
Affiliation:
International Center for Young Scientists, National Institute for Materials Science, Tsukuba-shi, Ibaraki 305-0047, Japan; and Department of Metallurgical and Materials Engineering, Middle East Technical University, 06531 Ankara, Turkey
Y.F. Liu
Affiliation:
International Center for Young Scientists, National Institute for Materials Science, Tsukuba-shi, Ibaraki 305-0047, Japan; and Department of Metallurgical and Materials Engineering, Middle East Technical University, 06531 Ankara, Turkey
Yutaka Kagawa*
Affiliation:
Research Center for Advanced Science and Technology, The University of Tokyo, Meguro-ku, Tokyo 153-8904, Japan
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

An all-oxide Al2O3-TiO2 ceramic multilayer composed of 10–100 nm thick alternating layers was fabricated using the reactive magnetron sputtering process. Microindentation tests were carried out on the multilayer ceramic followed by microstructural observations of the cross-sections of the indented sites to characterize the indentation response of the system. During the observations, it was noted that an extensive room temperature “deformation” occurred in the multilayer ceramic material. The material shows a thickness reduction of as much as ∼40% under a conical indenter at 300 mN of load without microcracking and dislocation-assisted deformation. The room temperature deformation mechanism is governed by the relative movement and rearrangement of the anisotropic nanoscale columnar grains along the intergranular boundaries containing elongated voids. The relative sliding along the intergranular boundaries, and the subsequent granular rotation under indentation were well captured by finite element simulation.

Keywords

SputteringCoatingMicrostructure
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 11 , November 2009 , pp. 3387 - 3396
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Kingery, W.D., Bowen, H.K., and Uhlmann, D.R.: Introduction to Ceramics (John Wiley & Sons, New York, NY, 1976).Google Scholar
2.Barsoum, M.W.: Fundamentals of Ceramics (Institute of Physics Publishing, Bristol, UK, 2003).CrossRefGoogle Scholar
3.Evans, A.G.: Design and life prediction issues for high-temperature engineering ceramics and their composites. Acta Mater. 45, 23 (1997).CrossRefGoogle Scholar
4.Lawn, B.R.: Fracture of Brittle Solids (Cambridge University Press, Cambridge, UK, 1993).CrossRefGoogle Scholar
5.Evans, A.G.: Perspective on the development of high-toughness ceramics. J. Am. Ceram. Soc. 73, 187 (1990).CrossRefGoogle Scholar
6.Lawn, B.R., Padture, N.P., Cai, H.D., and Guiberteau, F.: Making ceramics ductile. Science 263, 1114 (1994).CrossRefGoogle ScholarPubMed
7.Fischer-Cripps, A.C. and Lawn, B.R.: Stress analysis of contact deformation in quasi-plastic ceramics. J. Am. Ceram. Soc. 79, 2609 (1996).CrossRefGoogle Scholar
8.Lange, F.F.: Effect of microstructure on strength of Si3N4-SiC composite system. J. Am. Ceram. Soc. 56, 445 (1973).CrossRefGoogle Scholar
9.Faber, K.T. and Evans, A.G.: Intergranular crack-deflection toughening in silicon-carbide. J. Am. Ceram. Soc. 66, C94 (1983).CrossRefGoogle Scholar
10.Clegg, W.J., Kendall, K., Alford, N.M., Button, T.W., and Birchall, J.D.: A simple way to make tough ceramics. Nature 347, 455 (1990).CrossRefGoogle Scholar
11.An, L., Chan, H.M., Padture, N.P., and Lawn, B.R.: Damage-resistant alumina-based layer composites. J. Mater. Res. 11, 204 (1996).CrossRefGoogle Scholar
12.Liu, H.Y., Lawn, B.R., and Hsu, S.M.: Hertzian contact response of tailored silicon nitride multilayers. J. Am. Ceram. Soc. 79, 1009 (1996).CrossRefGoogle Scholar
13.Chawla, K.K., Coffin, C., and Xu, Z.R.: Interface engineering in oxide fibre/oxide matrix composites. Int. Mater. Rev. 45, 165 (2000).CrossRefGoogle Scholar
14.Cook, J. and Gordon, J.E.: A mechanism for the control of crack propagation in all-brittle systems. Proc. R. Soc. London, Ser. A 282, 508 (1964).Google Scholar
15.Phillipps, A.J., Clegg, W.J., and Clyne, T.W.: Fracture-behavior of ceramic laminates in bending. 1. Modeling of crack-propagation. Acta Metall. Mater. 41, 805 (1993).CrossRefGoogle Scholar
16.Phillipps, A.J., Clegg, W.J., and Clyne, T.W.: Fracture-behavior of ceramic laminates in bending. 2. Comparison of model predictions with experimental-data. Acta Metall. Mater. 41, 819 (1993).CrossRefGoogle Scholar
17.Folsom, C.A., Zok, F.W., and Lange, F.F.: Flexural properties of brittle multilayer materials. 1. Modeling. J. Am. Ceram. Soc. 77, 689 (1994).CrossRefGoogle Scholar
18.Folsom, C.A., Zok, F.W., and Lange, F.F.: Flexural properties of brittle multilayer materials. 2. Experiments. J. Am. Ceram. Soc. 77, 2081 (1994).CrossRefGoogle Scholar
19.Dericioglu, A.F.: Effect of microstructure on the mechanical behavior of reactive magnetron sputtered Al2O3/TiO2multilayer ceramics. Mater. Trans. 49, 2714 (2008).CrossRefGoogle Scholar
20.Brotzen, F.R.: Mechanical testing of thin-films. Int. Mater. Rev. 39, 24 (1994).CrossRefGoogle Scholar
21.Tabor, D.: The Hardness of Metals (oxford University Press, New York, NY, 1951).Google Scholar
22.Kelly, A.: Strong Solids (Claderon Press, oxford, UK, 1966).Google Scholar
23.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
24. ABAQUS User's Manuals: ABAQUS (ABAQUS Inc., Providence, RI, 2006).Google Scholar
25.Iuga, M., Steinle-Neumann, G., and Meinhardt, J.: Ab-initio simulation of elastic constants for some ceramic materials. Eur. Phys. J. B 58, 127 (2007).CrossRefGoogle Scholar
26.Lawn, B.R., Evans, A.G., and Marshall, D.B.: Elastic-plastic indentation damage in ceramics—The median-radial crack system. J. Am. Ceram. Soc. 63, 574 (1980).CrossRefGoogle Scholar
27.Veprek, S.: The search for novel, superhard materials. J. Vac. Sci. Technol., A 17, 2401 (1999).CrossRefGoogle Scholar
28.Dobrzanski, L.A., Pakula, D., Kriz, A., Sokovic, M., and Kopac, J.: Tribological properties of the PVD and CVD coatings deposited onto the nitride tool ceramics. J. Mater. Process. Technol. 175, 179 (2006).CrossRefGoogle Scholar
29.Panjan, P., Cekada, M., and Navinsek, B.: A new experimental method for studying the cracking behaviour of PVD multilayer coatings. Surf. Coat. Technol. 174, 55 (2003).CrossRefGoogle Scholar
30.Tanaka, M., Liu, Y.F. and Kagawa, Y.: Identification of delamination through TGO stresses due to indentation testing of an EBPVD TBC. J. Mater. Res. (2009, in press).CrossRefGoogle Scholar
31.Lloyd, S.J., Molina-Aldareguia, J.M., and Clegg, W.J.: Deformation under nanoindents in sapphire, spinel and magnesia examined using transmission electron microscopy. Philos. Mag. A 82, 1963 (2002).CrossRefGoogle Scholar
32.Tilbrook, M.T., Paton, D.J., Xie, Z., and Hoffman, M.: Microstructural effects on indentation failure mechanisms in TiN coatings: Finite element simulations. Acta Mater. 55, 2489 (2007).CrossRefGoogle Scholar
33.Ovid'ko, I.A.: Materials science—Deformation of nanostructures. Science 295, 2386 (2002).CrossRefGoogle ScholarPubMed